background image

 Door Operator / STA / LC- 2973 Rev.H– 15 

Operation with disengage mechanism

Warning! 

To avoid injury, the following points must 
be observed:-  
-  Drive units with a disengage mechanism 

require that a fall protection is mounted 
on to the door. 
- Without a fall protection the door does 
not comply with directive ASR. A1.7 and 
may fall in an uncontrolled manner

 

Pull on the red loop.

The door can be moved manually. 

 

Pull on the green loop.

The door can be moved with the operator. 

8.   Maintenance

Warning! 

To avoid damage to the operator and door, 
the following points must be observed:
- Maintenance must only be carried out by 
authorized persons.
- Directive BGR 232 must be complied with.
- Worn or faulty parts must be replaced.
- Only approved parts may be installed.
All maintenance work must be 
documented.

Information:

The drive unit has lifetime lubrication and 
is maintenance-free.

 

 

Check that all mountings have been securely 
tightened.

 

Check the brake (if available).

 

Check the limit switches and safety switches.

 

Check for noises and oil leaks.

 

Check the mounting of the operator for corrosion.

 

Check the housing for damage.

Summary of Contents for CDO 100: 1:10-30

















Reviews: