background image

1

dc2260af

DEMO MANUAL DC2260A

DESCRIPTION

LTC6811-2 

Addressable isoSPI Battery-

Stack Monitor

Demonstration circuit 2260A is an Addressable isoSPI 

Battery-Stack Monitor featuring the

 LTC6811-2

. Multiple 

boards can be linked through a 2-wire isolated serial in-

terface to monitor any number of cells on a stack. 
Communication to a PC uses a DC2026 Linduino

®

 One 

as a USB interface. The DC2026 comes preloaded with 

a legacy DC590 emulator function (the DC590 can also 

still be used

1

). A control program for up to ten stacked 

boards has a Graphical User Interface (GUI) to implement 

the device command set.
To control more than one DC2260A, the DC1941B isoSPI 

adapter and RJ45 (Ethernet) patch cables are also required.  

HARDWARE SETUP

When connected to a battery stack, power for the DC2260A 

is provided by the cell group being monitored. Separate 

the screw-terminal section from J1 and wire cell voltage 

connections or resistors into the clamping contacts to 

provide the input stimulus for the ADC.
Cell voltages are wired from position 4 (most negative 

potential of the group) with increasing potentials up to 

position 16 (most positive potential).

L

, LT, LTC, LTM, Linear Technology and the Linear logo and Linduino are registered 

trademarks and QuikEval is a trademark of Linear Technology Corporation. All other 

trademarks are the property of their respective owners.

Photo 1. Connecting a Board to a PC

Design files for this circuit board are available at  

http://www.linear.com/demo/DC2260A

Alternatively, for a simple demo, connect twelve 100Ω 

resistors between each contact from position 4 to position 

16 as shown in Figure 1. Then, provide a “stack-equivalent” 

power supply connection to position 16 (positive) and 

position 4 (return). The supply may be adjusted to provide 

the desired nominal cell voltage (e.g., 43.2V will be 3.6V/

cell). 

Note that cell discharge cannot be demonstrated 

properly with a resistor string stimulus

.

Photo 1 shows the following connections for one board 

interfaced to a PC:
1. Set jumpers on the board per Figure 1.
2. Connect a USB cable from the PC USB port to DC2026.
3. Connect a 14-pin ribbon from DC2026 to the SPI con-

nector (J2) on DC2260A.

4. Mate the J1 cell-voltage connector. The blue LED will 

illuminate when power is applied. The brightness reflects 

the supply current.

1

A DC590 is a USB data acquisition board that serves to interface the DC2259 to a PC’s USB 

port. This board is not necessary with a DC2026.

Summary of Contents for DC2260A












Reviews: