LINDR KONTAKT 55 Instruction Manual Download Page 5

FL

OW T

YPE luxur

y COOLER

 

5

 WARNING:

  Never place tools or other ob-

ject into the fan.

 WARNING:

  Never touch electrical compo-

nents with wet or damp hands.

 WARNING:

 To ensure the cooling unit 

works properly and at full capacity, make sure 

air supply to the unit is not obstructed.

 WARNING:

  Water temperature during sa-

nitation must not be higher than 25 °C!

 WARNING:

 Always make sure the power 

socket you intend to plug the cooler into is ac-

cessible, so that the appliance can be imme-

diately unplugged in case of emergency.

 WARNING:

 When unplugging the device 

from the socket, grab the plug and pull it out. 

Do not under any circumstances pull at the 

cable; risk of damage.

 WARNING

:  To turn the device off comple-

tely, unplug the appliance from the power soc-

ket.

 

WARNING:

  In the event the electrical wi-

ring of the product becomes damaged, sum-

mon a trained service technician. Do not under 

any circumstances repair the device yourself.

 WARNING:

 

The cooling system contains 

flammable coolant R290 (propane)!

 WARNING:

 Emergency maintenance and 

repair of the cooling system must be done by 

trained, authorised technicians familiar with 

cooling and electrical systems. The technicians 

should have special training and qualification 

for handling flammable substances in order to 

perform service on coolers containing  R290. 

Follow basic regulations and safety measures 

regarding service and repair!

 

WARNING:

  Do not use open flame or po-

tential sources of sparks in the vicinity of a 

cooler using 

R290 

coolant!

 WARNING:

  After unpacking, place the coo-

ler so that heat created by the cooling unit can 

be vented sufficiently.

 WARNING:

  Do not place objects that could 

prevent air circulation on top of the cooler.

5. INSTALLATION AND PLACEMENT:

Place the cooler onto a stable, level surface 

(maximum permitted inclination: 2 degrees). 

The appliance requires unobstructed air circu-

lation.

•  Ensure sufficient free space for air circulation 

and heat dissipation.

•  Ensure sufficient supply of fresh air.

•  The device must not be placed in an enclo-

sed space. 

•  The device must not be placed in the vicinity 

of heat sources or exposed to direct sunlight.

Minimum distance of vents from an obstac-

le that would limit air circulation must be 30 

cm. Minimum distance for sections with no air 

vents is 7 cm. Ideally, use the device in a cool 

and well-ventilated room. The device is desig-

ned for use at ambient temperature of at least 

16 °C and at most 32°C. 

 WARNING:

 

The device MUST NOT be used 

or stored at ambient temperature lower than 

0 °C.

 The device is designed for use in a normal 

environment, always under a roof, protected 

from rain or sunlight.  Climate class N. . 

  DANGER: 

  Protect the cooler and electri-

cal connection from rain and spraying water!

 WARNING:

  Do not under any circumstan-

ces lay the cooler on its side, not even during 

transport.

   NOTE:

  In order for the device to work 

correctly and at maximum output, it is im-

portant to not cover up any of the device‘s 

vents and ensure sufficient air circulation.

Summary of Contents for KONTAKT 55





















Reviews: