Lincoln IMPINGER 1100 Service Manual Download Page 5

Page: 5 / 72

Impinger II –1100 Series Service Manual - Domestic

S/N 2011383 and above

The speed side of the Time/Temp. Display uses a slotted disc Refer to page 27

(cemented to tach. coupling) to break the infra-red light beam of the optical

encoder (mounted on gear motor), producing electrical pulses that are transmitted

to the display. The display converts these pulses into a read-out of minutes and

seconds.

The temperature portion of the Time/Temp Display uses a Thermistor Probe to

sense oven temperature. The thermistor This resistance is then converted by the

display into a temperature reading.

AUTOMATIC COOL DOWN

When this oven is started, the time delay relay timing circuit is enabled, permitting

the oven fans to run for approximately 20 minutes after the oven is shutoff, to cool

the oven. The Time Delay Relay will keep the coil of the Main Fan Relay closed,

maintaining operation of main fan and Cooling Fan Motors.

Summary of Contents for IMPINGER 1100









































































Search results

Summary of Contents for IMPINGER 1100

Reviews:

Brands by name

Popular brands

Lincoln IMPINGER 1100, Service Manual

Search results

Summary of Contents for IMPINGER 1100

Reviews:

Brands by name

Popular brands