manualshive.com logo in svg

Lincoln IMPINGER 1100, Service Manual

Share
Download
Lincoln IMPINGER 1100 Service Manual Download Page 33

Impinger II –1100 Series Service Manual - Domestic 

33 

MOTOR, BURNER BLOWER  

 

This unit comes equipped to be used for other models of ovens.  For use on the 

Impinger II Series, the mating plug with the loose wires may be discarded. 

 

TO REMOVE BLOWER MOTOR: 

 

1.  Shut off power at main breaker. 

2.  Remove conveyor. 

3.  Remove control compartment covers. 

4.  Disconnect the plug on blower motor.  Plastic locks on side of plug need to be depressed. 

5.  Remove three screws holding blower horn to burner. 

6.  Remove air shutter from old unit and install on new unit.  If air shutter of old unit is damaged or lost, 

replace with new air shutter 369401. 

7.  Reassemble in reverse order. 

8.  Adjust air shutter opening if necessary.  Set air shutter at 50% open and adjust to get a blue flame with an 

occasional tip of yellow under high flame. A glass view port in the burner assembly should be used to 

observe flame. 

CLEANING OF THE BLOWER FAN IS NECESSARY ON A PREVENTIVE MAINTENANCE SCHEDULE. 

 

See Blower Wheel, Burner below 

 

BLOWER WHEEL, BURNER 

 

This is part of the burner blower motor assembly  

 

TO REMOVE THE BLOWER WHEEL FOR PERIODIC CLEANING

: 

1.  Disconnect power and remove control compartment covers. 

2.  Remove air shutter held by 3 screws. 

3.  Loosen set screw on blower wheel hub and pull straight out. 

4.  Reassemble in reverse order. 

NOTE

:   There is no critical placement of the blower wheel on the motor shaft.  Just 

back as far as it will go and then spin the blower to be sure it is not rubbing. 

 

AIR PRESSURE SWITCH 

 

1.  Shut off power at main breaker. 

2.  Remove conveyor. 

3.  Remove front control compartment cover. 

4.  Remove air switch cover plate. 

5.  Disconnect wiring and mark for reassembly. 

6.  Loosen 2 screws and remove air switch. 

7.  Disconnect 1/4" air tube. 

8.  Reassemble in reverse order. 

9.  Turn on power and calibrate air switch as follows: 

a)  Turn adjusting screw counter clockwise to full out position. 

b)  Turn main fan and heat switch on. 

c)  Turn adjusting screw clockwise until heat shuts off. 

d)  Turn adjusting screw (counterclockwise) 1/4 turn and unit should heat. 

NOTE: 

Test as follows 

e)  Oven must be tested in heated condition.

 

 

f)  Remove main fan fuse.  Main fan should shut down, deactivating air switch causing 

heat to shut off in approximately 5 to 25 seconds. 

g)  Fine tune adjustment as needed. 

 

Summary of Contents for IMPINGER 1100









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands