Lincoln 2006 Town Car Workshop Manual Download Page 23

Page: 23 / 45

Remove the fused jumpers.

Connect a fused jumper wire between:

HVAC module C228a-24, circuit 1379 (PK/LB), harness side and HVAC
module C228b-11, circuit 1566 (RD/YE), harness side.

HVAC module C228a-25, circuit 1380 (TN/YE), harness side and HVAC
module C228a-2, circuit 57 (BK), harness side.

Does the resistance smoothly increase and/or decrease when the jumpers
are connected?

F8 CHECK THE DOOR ACTUATOR OPERATION

NOTE:

If a jumper fuse opens while carrying out this test step, repair the circuit

(s) for a short.

With the fused jumper connections made as directed below, measure the
resistance between HVAC module C228a-20, circuit 438 (RD/WH), harness side
and HVAC module C228b-14, circuit 1130 (PK/LG), harness side.

Connect a fused jumper wire between:

HVAC module C228a-23, circuit 1376 (BK/LB), harness side and HVAC
module C228b-11, circuit 1566 (RD/YE), harness side.

HVAC module C228a-22, circuit 1375 (PK/YE), harness side and HVAC
module C228a-2, circuit 57 (BK), harness side.

Remove the fused jumpers.

Connect a fused jumper wire between:

HVAC module C228a-22, circuit 1375 (PK/YE), harness side and HVAC
module C228b-11, circuit 1566 (RD/YE), harness side.

HVAC module C228a-23, circuit 1376 (BK/LB), harness side and HVAC
module C228a-2, circuit 57 (BK), harness side.

Yes

INSPECT for broken door and linkage. REPAIR as necessary. If no condition is found,
GO to

F11

GO to

Page 23 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Summary of Contents for 2006 Town Car














































Search results

Summary of Contents for 2006 Town Car

Reviews:

Related manuals for 2006 Town Car

Brands by name

Popular brands

Lincoln 2006 Town Car, Workshop Manual

Search results

Summary of Contents for 2006 Town Car

Reviews:

Related manuals for 2006 Town Car

Brands by name

Popular brands