manualshive.com logo in svg

Lincoln 2006 Town Car, Workshop Manual

The Lincoln 2006 Town Car Quick Reference Manual is a comprehensive guide for owners of this elegant vehicle. You can easily download this manual from our website for free, providing you with all the necessary information and instructions to make the most of your Town Car experience.

Share
Download
background image

  

Does the resistance smoothly increase and/or decrease when the jumpers 
are connected?

 

 

F9 CHECK THE ACTUATOR MOTOR DRIVE CIRCUITS FOR AN OPEN

 

NOTE: 

Access to the connector in the following step is difficult. Before 

performing this step, visually inspect the actuator and its harness for obvious 
damage. If no damage is evident, proceed with the test. 

Ignition OFF.  

Disconnect: 

For DTC B1263

, Panel/Defrost Door Actuator C2248.  

Disconnect: 

For DTC B1264

, Floor Door Actuator C234. 

DTC B1263 

  

NOTE: 

For 

DTC B1263

 only.  

Measure the resistance between HVAC module C228a-24, circuit 1379 (PK/LB), 
harness side and panel/defrost door actuator C2248-1, circuit 1379 (PK/LB), 
harness side. 

DTC B1263 

  

NOTE: 

For 

DTC B1263

 only.  

Measure the resistance between HVAC module C228a-25, circuit 1380 (TN/YE), 
harness side and panel/defrost door actuator C2248-6, circuit 1380 (TN/YE), 
harness side. 

DTC B1264 

  

NOTE: 

For 

DTC B1264

 only.  

Measure the resistance between HVAC module C228a-22, circuit 1375 (PK/YE), 
harness side and floor door actuator C234-1, circuit 1375 (PK/YE), harness side. 

DTC B1264 

Yes

 

INSPECT for broken door and linkage. REPAIR as necessary. If no condition is found, 
GO to 

F10

.  

 

No

 

REPAIR the circuit(s) for an open. CLEAR the DTCs. REPEAT the self-test. TEST the 
system for normal operation.

Page 24 of 45

2006 Town Car Workshop Manual

12/30/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS6G/~MUS~LEN/19/...

Summary of Contents for 2006 Town Car














































Reviews:

No comments

Related manuals for 2006 Town Car

Hama Cup holder Operating Instruction preview
Cup holder
Brand: Hama Pages: 2
Abarth 124 SPIDER Service And Warranty Handbook preview
124 SPIDER
Brand: Abarth Pages: 36
Wagan 2591 User Manual preview
2591
Brand: Wagan Pages: 12
RAM 2015 1500 User Manual preview
2015 1500
Brand: RAM Pages: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Brand: RAM Pages: 116
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Brand: Air Lift Pages: 12
Quadratec 12226.3011 Installation Manual preview
12226.3011
Brand: Quadratec Pages: 8
Quadratec 12057.0261 Installation Manual preview
12057.0261
Brand: Quadratec Pages: 12
Mazda 2006 RX-8 Service Highlights preview
2006 RX-8
Brand: Mazda Pages: 122
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Brand: Jeep Pages: 136
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Brand: Whispbar Pages: 15
Fab Fours H4550 Installation Instructions Manual preview
H4550
Brand: Fab Fours Pages: 13
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Brand: Vauxhall Pages: 131
Camoplast T4S Installation Manuallines preview
T4S
Brand: Camoplast Pages: 19
Fab Fours C3150 Installation Instructions Manual preview
C3150
Brand: Fab Fours Pages: 21
Toyota Solara guide Owner'S Manual preview
Solara guide
Brand: Toyota Pages: 497
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Brand: KLAUS Multiparking Pages: 72
Carcomm CMPC-22 Fujitsu-Siemens PocketLoox 410 Installation Manual preview
CMPC-22 Fujitsu-Siemens PocketLoox 410
Brand: Carcomm Pages: 2

Brands by name

Popular brands

Load more brands