manualshive.com logo in svg

Lincoln Electric Vantage 441X/LE500X, Operator'S Manual

Share
Download
Lincoln Electric Vantage 441X/LE500X Operator'S Manual Download Page 51

E-3

TROUBLESHOOTING

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your  
Lincoln Authorized Service Facility for technical troubleshooting assistance before you proceed. 

WWW.LINCOLNELECTRIC.COM/LOCATOR

PROBLEMS 

(SYMPTOMS)

POSSIBLE  

CAUSE

RECOMMENDED 

COURSE OF ACTION

Battery does not stay charged. 

Engine  will  not  idle  down  to  low 
speed. 

Engine will not go to high idle when 
attempting to weld. 

Engine will not go to high idle when 
using auxiliary power. 

1. Faulty battery.
2. Faulty engine alternator.
3. Loose or broken lead in charging
circuit.
4. Loose fan belt may need
tightening.

1. Idler switch in HIGH idle position,

make sure switch is set to AUTO.

2. Check Engine CAN Leads for

proper connection.

1. Poor work lead connection to
work.
2. Welding Terminals switch in wrong
position.
3. No open circuit voltage at output
studs.
4. Check Engine CAN Leads for
proper connection

1. Broken wire in auxiliary current
sensing wiring.
2. Auxiliary power load is less than
100 watts.
3. Check Engine CAN Leads for
proper connection

If all recommended possible areas 
of misadjustment have been 
checked and the problem persists, 

Contact your local Lincoln 
Authorized Field Service Facility. 

FUNCTION PROBLEMS

Observe all Safety Guidelines detailed throughout this manual

Engine  goes  to  low  idle  but  does 
not stay at low idle. 

1. Incorrect winding on auxiliary
toroid.
2. Check wiring for weld circuit to
ground.

No  welding  output  or  auxiliary  out-
put. 

1.

Broken lead in rotor circuit.

2.

Faulty field diode module.

3.

Faulty rotor.

Welder has some/ no output and no 
control. Auxiliary output OK 

1. Faulty remote kit.

2. Faulty output control

potentiometer.

3. Faulty output control wiring.

4. Faulty CHUI PCB or Chopper

PCB.
 

No  welding  output.  Auxiliary  output 
OK. 

1. WELDING TERMINALS switch in

wrong position, be sure switch is

in WELDING TERMINALS ON

position.

2. Faulty CHUI PCB or Chopper

PCB.

VANTAGE

®

 441X

/LE500X

 

Summary of Contents for Vantage 441X/LE500X


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands