manualshive.com logo in svg

Lincoln Electric Vantage 441X/LE500X, Operator'S Manual

Share
Download
Lincoln Electric Vantage 441X/LE500X Operator'S Manual Download Page 50

E-2

TROUBLESHOOTING

Observe all Safety Guidelines detailed throughout this manual

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your  
Lincoln Authorized Service Facility for technical troubleshooting assistance before you proceed. 

WWW.LINCOLNELECTRIC.COM/LOCATOR

PROBLEMS 

(SYMPTOMS)

POSSIBLE  

CAUSE 

RECOMMENDED 

COURSE OF ACTION

Major Physical or Electrical Damage 
is Evident. 
Engine will not crank 

Engine will crank but not start. 

Engine shuts down shortly after starting. 

Engine shuts down while under a load. 

Engine runs rough. 

Engine will not shut off.

 

1

. Contact  your  Local  Lincoln

Authorized Field Service Facility.

1. Battery low.
2. Loose battery cable connections
which may need Inspected, cleaned
or tighten.
3. Faulty wiring in engine starting circuit.
4. Faulty engine starter. Contact
authorized
local Engine Service Shop.
5. If check engine light is on contact
your Field Service Facility.
6. Check 20A Breaker CB7 (Starter
Relay).
1. Out of fuel.
2. Fuel shut off valve is in the off position
make sure the valve lever is in the open
position (lever in-line with the Hose).
3. Engine shut down solenoid not pulling
in.
4. Fuel Filters dirty/clogged, main filter
element and/or Inline Fuel Filter may
need to be replaced.
5. High oil temperature or low oil
pressure (engine protection light lit).
6. Check 5A breaker CB11.

1. Dirty fuel or air filters may need
cleaned/replaced.
2. Water in fuel.

1. Fuel Shutdown solenoid not functioning
properly.

If  all  recommended  possible  areas 
of  misadjustment  have  been 
checked and the problem persists, 

Contact  your  local  Lincoln 
Authorized Field Service Facility. 

ENGINE PROBLEMS

1. Low oil pressure (engine protection
light lit). Check oil level (Consult
engine service dealer).
2. High oil temperature. Check engine
cooling system. (engine protection
light lit).
3. Faulty oil pressure switch.
4. Faulty oil temperature switch. Contact
authorized local Engine Service Shop.
5. Check coolant level.

1. High oil temperature.
2. High coolant temperature.
3. Low oil pressure.

VANTAGE

®

 441X

/LE500X

 

Summary of Contents for Vantage 441X/LE500X


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands