Lincoln Electric Vantage 441X/LE500X Operator'S Manual Download Page 41

Page: 41 / 57

C-2

ACCESSORIES

TIG Module

Supplies high frequency for superior starting, contactor control,

remote control capability, and a gas valve for AC or DC TIG

welding.
Order:

K930-2 TIG Module
K936-1 TIG Module Cable, 9 pin to 14 pin

WIRE FEEDERS & GUNS

K126 Pro Innershield

Gun

Feature replaceable liners, interchangeable backend, long life

Magnum

PRO contact tips, improved heat resistant gun tubes,

and better trigger lead protection. For self-shielded .062-5/64 in.

(1.6-2.0 mm) wire with 15 ft. (4.5 m) cable. Includes K466-10

Connector Kit.
Order: K126-12

Magnum SG Spool Gun

25.ft (7.6m) handheld semiautomatic wire feeder large easy-grip

handle and remote control wire speed. Requires Control Module

and Input Cable.
Order: K487-25 Magnum SG

K488 Magnum Control Module
K691-10 Input Cable

Power Feed 25M

Compact wire feeder offers push-pull capable for premium

aluminum welding. Features the MAXTRAC

drive system, full

controls, and procedural memory presets to support the advanced

process welding on almost any application. Plastic and aluminum

case available. ArcLink

control cable needed.

Order:

K2536-5 Plastic Case
K2536-4 Aluminum Case
K2683-25 Heavy Duty ArcLink

Control Cable - 25 ft.

(7.6 m)
K2683-50 Heavy Duty ArcLink

Control Cable - 50 ft.

(15.2 m)
K2683-100 Heavy Duty ArcLink

Control Cable - 100

ft. (30.4 m)
K2429-1 ArcLink

"T" Connector Kit

POWER SOURCES

Square Wave TIG 200

Portable TIG and stick welding machine that provides smooth and

stable AC TIG welding on aluminum and DC TIG welding on steel,

stainless steel and chrome-moly.
Order: K5126-1

PowerMIG 210MP

Multi-process welder with MIG, stick, TIG, and flux-cored welding.

The push-and-turn digital controls and color display screen make

setup and operation intuitive and easy, while the all-metal wire

drive and sturdy sheet-metal construction make it rugged and

ready for any job. Runs off auxiliary power to provide an additional

welding arc.
Order: K3963-1

Tomahawk 1000 Plasma Cutter

Cuts metal using the AC generator power from the engine-driven

welder. Requires the T12153-10 Full-KVA Power Plug (NEMA 15-

50P).
Order: K2808-1

Multi-Weld 350

Small and portable welder to provide additional welding arcs.

Multiple machines can be powered off the welding power cable of

one main power supply. Excellent option to provide control at the

welding arc for DC+ stick or wire processes.
Order: K1735-1

Invertec V350 PRO

Efficient, lightweight, and portable multi-process welder. Runs off

the auxiliary power to provide an additional welding arc.
Order: K1728-6

Invertec V275-S

Proven, portable CC power source for Stick or TIG welding. Runs

off the auxiliary power to provide an additional welding arc.
Order: K2269-1

CABLE ACCESSORIES

Tweco

Adaptors

Allows for quick cable changeovers on the jobsite.
Order:

K2487-1 Stud to Tweco Female Adapter – LENCO (CT-

40FS)

K2946-1 Tweco Style Cam-Lock Adapter Plug for 2/0

(50 mm

) cable

K3416-70 Tweco Style Plug (Male, 1/0 thru 2/0)
K3416-90 Tweco Style Plug (Male, 3/0 thru 4/0)
K3417-70 Tweco Style Receptacle (Female, 1/0 thru

2/0)
K3417-90 Tweco Style Receptacle (Female, 3/0 thru

4/0)

Flextec 350X PowerConnect

Reliable, multi-process welder designed for use in construction,

fabrication, shipbuilding, and other heavy-duty applications.

Features PowerConnect Technology to allow for automatic

connecting to any incoming voltage including 200-575 VAC, single

or three phase phase, 50 or 60 Hz.
Order: K4273-1

VANTAGE

441X

/LE500X

Summary of Contents for Vantage 441X/LE500X


























































Search results

Summary of Contents for Vantage 441X/LE500X

Reviews:

Brands by name

Popular brands

Lincoln Electric Vantage 441X/LE500X, Operator'S Manual

Search results

Summary of Contents for Vantage 441X/LE500X

Reviews:

Brands by name

Popular brands