manualshive.com logo in svg

Lincoln Electric SAE-300 HE, Operator'S Manual, Page: 10 / 35

Share
Download
Lincoln Electric SAE-300 HE Operator'S Manual Download Page 10

A-3

INSTALLATION   

SAE-300

®

HE

A-3

Welder  Enclosure

- The complete welder is rubber

mountedonaruggedsteel“C”channelbase.

The output terminals are placed at the side of the
machinessothattheyareprotectedbythedoor.The
outputterminalsarel)and(-).

Cranking  System

- A 12 volt electric starter is stan-

dard.

Air Cleaner

-Heavydutytwostagedrytype.

Muffler

- A muffler and stainless steel exhaust outlet

elbowarestandard.

Fuel / Hour / LED gauge

-Ametertorecordhoursof

operation,showfuelstatus,batterychargingfaultLED
andenginefaultLED.

Engine  Protection  - 

The system shuts the engine

down in the event of sudden low oil pressure or high
coolant temperature. A warning light on the control
panelwillindicatesuchafault.Toresettheenginefor
restarting,turntheignitionswitchoffthenon.Referto
Troubleshooting section for all warning light fault
codes.

Battery Charging Light - 

Awarningindicatorlightfor

Low/Nobatterycharge.Thelightisoffwhenthesys-
temsarefunctioningproperly.Thelightwillcomeonif
there is a Low/No battery condition but the machine
willcontinuetorun.

NOTE

: The light will come on when the Run/Stop

switch is in the “ON” position. It will come on during
cranking and stay on until the engine starts. After,
starting the engine the light will go off unless a
Low/Nobatteryconditionexists.

Oil  Drain  Valve  - 

A ball valve, hose and clamp are

standard.

Remote Control 

- The Remote / Local Switch and

Receptaclearestandard.

PRE-OPERATION  INSTALLATION

ExHAUST SPARK ARRESTER

Some federal, state or local laws may require that
engines be equipped with exhaust spark arresters
when they are operated in certain locations where
unarrested sparks may present a fire hazard.  The
standard muffler included with this welder does not
qualify as a spark arrester.  When required by local
regulations,asuitablesparkarrestermustbeinstalled
andproperlymaintained.

Useofanincorrectarrestermayleadtoenginedamage
or performance loss.  Contact the engine manufacturer
forspecificrecommendations.

------------------------------------------------------------------------

LOCATION / VENTILATION 

Always operate the welder with the doors closed.
Leavingthedoorsopenchangesthedesignedairflow
andmaycauseoverheating.

Theweldershouldbelocatedtoprovideanunrestrict-
ed flow of clean, cool air.  Also, locate the welder so
that engine exhaust fumes are properly vented to an
outsidearea.

Do  not  attempt  to  use  this  equipment  until  you
have  thoroughly  read  the  engine  manufacturer’s
manual  supplied  with  your  welder.  It  includes
important  safety  precautions,  detailed  engine
starting,  operating  and  maintenance  instructions,
and parts lists.

------------------------------------------------------------------------

ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or

electrode with skin or wet clothing.

• Insulate  yourself  from  work  and

ground

• Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE ExHAUST can kill.
• Use  in  open,  well  ventilated  areas  or

vent exhaust outside.

------------------------------------------------------------------------

MOVING PARTS can injure.
• Do  not  operate  with  doors  open  or

guards off.

• Stop engine before servicing.
• Keep away from moving parts.

------------------------------------------------------------------------

See additional warning information at the

front of this operator’s manual.

-----------------------------------------------------------

WARNING

CAUTION

Summary of Contents for SAE-300 HE




































Reviews:

No comments