background image

A-2

INSTALLATION   

A-2

SELECT SUITABLE LOCATION

The Invertec EX350i will operate in harsh environ-
ments. Even so, it is important that simple preventa-
tive measures are followed in order to assure long life
and reliable operation.

• The machine must be located where there is free cir-

culation of clean air such that air movement in the
back, out the sides and bottom will not be restricted.

• Dirt and dust that can be drawn into the machine

should be kept to a minimum. Failure to observe
these precautions can result in excessive operating
temperatures and nuisance shutdown.

• Keep machine dry. Shelter from rain and snow. Do

not place on wet ground or in puddles.

•  DO NOT MOUNT OVER COMBUSTIBLE SURFACES.

Where there is a combustible surface directly under
stationary or fixed electrical equipment, that surface
shall be covered with a steel plate at least
.06”(1.6mm) thick, which shall extend not less than
5.90”(150mm) beyond the equipment on all sides.

STACKING

EX350i cannot be stacked.

TILTING

Place the machine directly on a secure, level surface
or on a recommended undercarriage. The machine
may topple over if this procedure is not followed.

INPUT AND GROUNDING CONNECTIONS

•  Only a qualified electrician should connect the

Invertec EX350i. Installation should be made in
accordance with the appropriate National Electrical
Code, all local codes and the information detailed
below.

• When received directly from the factory, multiple

voltage machines are internally connected for
460VAC. If 460VAC is the desired input, then the
machine may be connected to the power system
without any setup required inside the machine.

• Initial 200VAC - 415VAC and 575VAC opera-

tion will require an Input voltage panel setup.

SAFETY PRECAUTIONS

ELECTRIC SHOCK 

can kill

.     

• TURN THE INPUT POWER OFF AT 
THE DISCONNECT SWITCH BEFORE
ATTEMPTING TO CONNECT OR DIS-

CONNECT INPUT POWER LINES, OUTPUT
CABLES, OR CONTROL CABLES.

• Only qualified personnel should perform this

installation.

• Connect the green/yellow lead of the power

cord to ground per U.S.National Electrical
Code.

----------------------------------------------------------------------

WARNING

• Open the access panel on the rear of the machine.
• For 200 or 230: Position the large switch to 200-

230.

For higher voltages: Position the large switch to
380-575.  

• Move the "A" lead to the appropriate terminal.

POWER CORD CONNECTION

A 25 ft. power cord is provided and wired into the
machine. Follow the power cord connection instruc-
tions. 

• 

Incorrect connection may result in equipment
damage.

-----------------------------------------------------------------------

Single Phase Input

Connect green lead to ground per National Electrical
Code.
Connect black and white or brown leads to power.
Wrap red lead with tape to provide 600V insulation.

Three Phase Input

Connect green lead to ground per National Electric
Code.
Connect black, red and white leads to power.

CONNECTIONS OF WIRE FEEDERS TO EX350I

LN-25 Connection Instructions 

-

Not recommended for Pulse Welding with the

Advanced Process Kit 

).

• Turn the EX350i power switch "off".

• Connect the electrode cable to the output terminal of

polarity required by electrode. Connect the work lead
to the other terminal.

• LN-25 with Remote Control options can be used with

the EX350i. The 14 pin (K444-2) remote can be con-
nected directly to the 14 pin amphenol. The 42 Volt
Remote Voltage and Output Control (K624-1) Kit can
be connected to the EX350i 24/42 VAC amphenol
using Remote Control Cable assembly K627- [ ]. LN-
25s with a K431-1 remote kit can be connected to
the 24/42 VAC amphenol using a K432 cable and a
K876 adapter. (See connection diagram S19899) to
connect it to one of the 14-pin amphenols. Or the
K432 cable could be modified with a K867 Universal
Adapter Plug (See connection diagram S19405) to
connect it to the 24/42 VAC 14-pin amphenol. 

W

AR

NIN

G

RE

M

OT

E

PO

W

ER

OF

F

ON

A

  

A

M

P

S

A

V

  

V

O

LT

S

W

EL

D TE

RM

INA

LS

SE

LE

CT

O

U

TP

U

T

LIN

CO

LN

EL

EC

TR

IC

INVER

TEC V350-PRO

W

AR

NIN

G

W

AR

NIN

G

AV

IS

O DE

PR

EC

AUC

IO

N

AT

TE

NTIO

N

!

!

!

!

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r a

dip

iscin

g

Lore

m ip

sum

 do

lor sit 

amet 

con

se

cte

tuer

 adipi

scing

 elit, 

ed d

iam

 no

num

my 

nib

h e

uism

od t

incid

unt u

t

 elit,

 ed

 dia

m n

onu

mmy 

nibh

 eu

ismod 

tinc

idu

nt u

t

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 lao

reet do

lore 

ma

gna

 aliq

uam

 erat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lo

rem 

ipsu

m d

olo

r si

t amet 

co

nse

cte

tuer 

adi

pisc

ing

 elit

, ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt 

ut

 el

it, ed 

dia

non

umm

y n

ibh eu

ismod

 tinc

idun

t u

t

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 laore

et d

olo

re m

agn

a al

iqu

am

 erat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m i

psum 

dol

or 

sit ame

t co

nsec

tetu

er a

dip

iscin

g

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt 

ut

 elit,

 ed d

iam

 nonum

my nib

h eu

ism

od t

inc

idun

t ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 la

oreet

 do

lore

 ma

gna al

iqu

am

 erat

 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m ipsu

m do

lor sit a

met co

nse

cte

tue

r a

dip

isci

ng

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt 

ut

 el

it, e

d di

am

 no

num

my n

ibh

 eu

ismo

d tin

cidunt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 la

ore

et do

lore 

magn

a a

liqu

am 

era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m ip

sum

 dolo

r si

t am

et c

onse

cte

tue

r adipisci

ng

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 elit,

 ed

 diam 

no

numm

y n

ibh

 eu

ism

od t

incid

unt

 ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 erat

 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

ips

um

 do

lor sit

 am

et co

nse

cte

tue

r a

dip

isc

ing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt 

ut

 eli

t, ed 

dia

m n

onu

mmy ni

bh

 eu

ism

od tin

cidun

t ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 lao

reet

 dol

ore

 m

agn

a a

liqu

am 

era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m ip

su

dolor sit

 am

et conse

ctetue

r ad

ipis

cing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

inci

dun

t ut

 elit,

 ed di

am

 non

um

my 

nib

h eu

ismod tin

cidu

nt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 la

oreet do

lore

 m

agna

 al

iqua

m era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lo

rem

 ipsum

 do

lor s

it a

met 

co

nse

cte

tuer ad

ipis

cin

g

 elit

, ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 elit,

 ed

 dia

nonu

mm

y n

ibh

 eui

smo

d t

inci

dunt ut

 lao

ree

t d

olo

re m

agn

a a

liqu

am

 era

 lao

ree

t dol

ore m

agna 

aliquam

 era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lo

rem

 ips

um

 do

lor 

sit a

me

t cons

ect

etu

er ad

ipisc

ing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 elit,

 ed

 dia

m non

um

my nibh euism

od ti

nci

dunt ut

 lao

ree

t d

olo

re m

agn

a a

liqu

am

 era

 lao

reet

 dolor

e magn

a al

iqu

am

 era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m ipsum

 dolor 

sit a

me

t con

se

cte

tuer

 ad

ipis

cing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt u

t

 elit

, ed di

am 

non

ummy 

nib

h e

uism

od tin

cidu

nt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 laoree

t dol

ore m

agn

a a

liquam

 era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r a

dip

isci

ng

Lorem 

ipsu

m dol

or 

sit a

me

t co

nse

cte

tuer

 adi

pisci

ng

 elit, 

ed d

iam

 no

num

my 

nib

h e

uism

od t

incid

unt 

ut

 elit, 

ed d

iam

 nonu

mmy n

ibh eu

ism

od tin

cidu

nt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 lao

ree

t dol

ore 

magna ali

quam erat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cin

g

Lor

em 

ips

um

 dolo

r sit 

amet 

co

nse

cte

tue

r adi

pisc

ing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 elit, ed

 diam 

non

umm

y n

ibh e

uis

mo

d tin

cidu

nt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 la

ore

et do

lore 

ma

gna

 aliq

uam e

rat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m ip

su

m d

olor

 sit a

met 

co

nsec

tetu

er ad

ipis

cing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 elit, 

ed diam 

non

ummy

 nib

h e

uismod ti

ncid

unt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 lao

ree

t dol

ore

 m

agna 

aliq

uam

 er

at 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lorem ipsu

m dolor s

it a

met consec

tetuer

 ad

ipis

cing

 elit, 

ed d

iam

 no

num

my n

ibh

 eu

ism

od t

incid

unt u

t

 elit

, e

d d

iam

 nonummy nibh euismod 

tinc

idun

t u

t

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 laore

et d

olore

 magna

 aliquam

 erat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lore

m ipsum dolor sit

 am

et cons

ecte

tuer adipiscing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 eli

t, ed diam

 non

um

my

 ni

bh eu

ismo

d tin

cidu

nt ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 laoreet

 dolo

re m

agna

 aliq

ua

erat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r a

dip

iscin

g

Lor

em ipsum do

lor 

sit amet con

sec

tetu

er adipis

cing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od ti

ncid

unt 

ut

 elit

, ed

 dia

m n

onu

mmy nibh

 eui

smod tincidunt u

t

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 la

ore

et dolore 

magn

a a

liquam 

erat 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lorem

 ipsum d

olor

 sit a

me

t cons

ectet

uer a

dip

isc

ing

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt 

ut

 elit

, ed

 dia

nonu

mm

y nibh eu

ismod tinc

idun

t ut

 lao

ree

t d

olo

re m

agn

a a

liqu

am

 era

 laoree

t dol

ore magna

 aliqu

am 

era

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cing

Lor

em 

ips

um d

olor 

sit am

et c

onse

ctet

uer ad

ipisc

ing

 elit, 

ed d

iam

 no

num

my 

nib

h e

uism

od t

incid

unt u

t

 eli

t, ed 

diam

 no

nu

mm

y nibh

 euismod t

incid

unt 

ut

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 lao

reet

 dolor

e ma

gna 

aliq

uam er

at 

Lore

m ip

sum

 do

lor s

it a

me

t co

nse

cte

tue

r ad

ipis

cin

g

Lore

m ips

um

 do

lor s

it ame

t cons

ect

etu

er 

adipi

sci

ng

 elit,

 ed

 dia

m n

onu

mm

y n

ibh

 eu

ism

od t

incid

unt 

ut

 eli

t, e

d d

iam

 nonum

my ni

bh e

uis

mod ti

nci

dun

t u

t

 lao

ree

t do

lore

 m

agn

a a

liqu

am

 era

 laor

eet 

dolo

re ma

gn

a a

liqu

am erat 

GREEN

RED

BLACK

WHITE or BROWN

EX350i

CAUTION

CAUTION

Summary of Contents for Red-D-Arc EX350i









































Reviews: