Lincoln Electric Ranger 330MPX Operator'S Manual Download Page 10

Page: 10 / 56

A-1

INSTALLATION

RANGER

330MPX

TECHNICAL SPECIFICATIONS -

RANgER 330MPX (KOHLER) (K3459-1)

Lift bail rating 1085 lb (492 kg) Maximum.

IEC 60974-1; IP23

-10°C TO +40°C OPERATING RANGE.

gENERAL DESCRIPTION

The Ranger

330MPX is a compact, versatile machine for a wide

variety of applications. They are well suited for service trucks,
maintenance, repairs, pipeline welding, farm and ranch work, and
back-up power.

The small size and low weight allows more room for trucks to
carry tools and other equipment.

The fully sealed display guides welders to the best settings for
making a quality weld.

Low sound improves work place safety and may qualify the
machine for low noise regions, such as near schools or hospitals.

Auxiliary power quality is the best in its class – less than 5% total
harmonic distortion throughout the entire power range. Quality of
the auxiliary power is fully independent of the weld setting.

Direct connect spool gun makes wire welding easy and
inexpensive.

AUXILIARY OUTPUT @ 104 °F (40°C)

CONTINUOUS

PEAK

RECEPTACLE

CIRCUIT

BREAKER

Single
Phase
60Hz

10,000 Watts

11,500
Watts

120 VAC Duplex
(5-20R) GFCI
Protected

20 Amps

120/240 VAC
Dual Voltage Full
KVA (14-50R)

50 Amps

240 VAC (6-50R) 50 Amps

ENGINE SPECIFICATIONS

Make/Model

Kohler carb

CH740 (25 hp) for Ranger 330MPX

EPA Emission

Evaporative

Displacement

44.2 cu. in. (724 cc)

Speed

3600 rpm @ full load
2500 rpm for low idle

Warranty (USA)

2 year complete (parts and labor)

3 year major components (parts and labor)

Battery

12VDC Battery

BCI group size 99

410 cold cranking amps

Fuel System

Electric lift pump, carburetor

Air Cleaner

Dual Element

Lubrication

Full pressure with full flow filter

Engine Protection Low Oil Pressure "Protection Switch"

Capacities

Fuel: 11 gal (41.6 L) Gasoline

Oil: 1.7 - 1.9 qts (1.6 - 1.8 L) 10W-30

WELDING RATED OUTPUT @ 104°F (40°C)

MODEL

WELDING PROCESS WELDING OUTPUT – IEC RATING

Current/Voltage/Duty Cycle

OTHER RATINGS

MAXIMUM WELD OCV

@ RATED LOAD RPM

Ranger 330MPX

DC Stick Welding
(constant current)

35 A / 21.4 V / 100 %

330A/ 28V /100%

85 Volts

292 A / 31.7 V / 100%

DC Pipe Welding

35 A / 21.4 V / 100 %

330A/ 28V /100%

85 Volts

292 A / 31.7 V / 100%

Touch-Start TIG

25 A / 11 V / 100%

330A/ 28V /100%

24 Volts

325 A / 23.0 V / 100%

DC MIG/FCAW Welding
(Constant Voltage)

35 A / 15.8 V / 100%

330A / 28V / 100%

85 Volts

312A / 29.6V / 100%

DC Arc Gouging

330A / 28V /100%

85 Volts

Summary of Contents for Ranger 330MPX

























































Search results

Summary of Contents for Ranger 330MPX

Reviews:

Brands by name

Popular brands

Lincoln Electric Ranger 330MPX, Operator'S Manual

Search results

Summary of Contents for Ranger 330MPX

Reviews:

Brands by name

Popular brands