manualshive.com logo in svg

Lincoln Electric INVERTEC V300-I, Service Manual

Share
Download
Lincoln Electric INVERTEC V300-I Service Manual Download Page 61

INVERTEC V300-I

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-18 

TROUBLESHOOTING & REPAIR      

TEST PROCEDURE

1. Move Output Terminal Switch S4 to ON

position.

Adjust the output control to the minimum
setting. Place the mode control at the
SMAW (soft) position.

NOTE: This test should only be conducted
when the machine reconnect switch and
jumper are set for high voltage (above 380
VAC) and the proper line voltage is applied.

DYNAMIC CAPACITOR BALANCE TEST

ELECTRIC SHOCK can kill.

Observe all safety precautions detailed
throughout this manual.

WARNING

-

+

OUTPUT TERMINAL SWITCH S4
(ON) POSITION

LINCOLN

FIGURE F.10 — OUTPUT TERMINAL SWITCH IN ON POSITION.

Summary of Contents for INVERTEC V300-I



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands