manualshive.com logo in svg

Lincoln Electric INVERTEC V300-I, Service Manual

Share
Download
Lincoln Electric INVERTEC V300-I Service Manual Download Page 54

INVERTEC V300-I

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-11 

TROUBLESHOOTING & REPAIR    

4. Slide the through bolts toward the

Control Panel until the brackets are dis-
connected and resistors are loose.  Be
careful when loosening these through
bolts, as they secure the two resistors.
As the through bolts are removed, care-
fully place the resistors and the connect-
ed wires to the side.

TEST PROCEDURE

1. Turn main power OFF.

2. Perform Input Filter Capacitor

Discharge procedure detailed in
Maintenance section. 

3. Remove the two through bolts that attach

the Power/Drive Board bracket to
Protection/Input Rectifier bracket.  Each
through bolt also supports a resistor.

ELECTRIC SHOCK can kill.

Observe all safety precautions detailed
throughout this manual.

– Perform input filter capaciter discharge

procedure.

WARNING

PROTECTION BOARD OUTPUT TEST

FIGURE F.4 — REMOVING THROUGH BOLTS.

Summary of Contents for INVERTEC V300-I



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands