Lince ZENITH GOLD 869 Series Installation, Operation And Maintenance Manual Download Page 4

4

LINCE ITALIA S.p.A.

9511-GOLD-RC

Wireless remote control for control panel management. All combinations related to arming, sectioning, choice of 

programs and disarming can be implemented with just two buttons. The three signal LEDs allow you to make 

selections (program type), using the first button, and confirm the choice made, using the second button. Aesthetically 

pleasing and ergonomic in use. Completely bidirectional, it receives the command execution response from the 

control panel. It allows you to view the system state, open input and alarm memory. 

OBLO 869 SIRENS

Its design is based on a new concept to facilitate installation and maintenance. The siren is made entirely of 

polycarbonate, resistant to impact and UV rays; its unconventional aesthetics distinguish it among many. Powered 

by a non-rechargeable lithium battery (art. 001515/00251AA, not supplied) it is also equipped with a WIN (Wired 

Interface Network) power supply system that allows the siren to be powered in three different modes: non-

rechargeable lithium (not supplied) - non-rechargeable lithium with mains power supply via 12 Vdc adapter (not 

supplied) - lead battery 12 V 2.2 Ah (not supplied) with mains power supply via 12 Vdc adapter (not supplied). The 

sound frequency is 1,800 Hz and the sound pressure - volume, adjustable from the control panel - is 115 dB @ 1 m 

if battery powered and 119 dB @ 1 m if powered by win. Maximum continuous acoustic alarm time of 3 min if battery 

powered and 5 min if powered by win. The siren is protected from being opened, tampered with and wall removed 

by means of a micro switch. Optical signalling occurs by means of a high efficiency LED. The electronic board has 

been designed and epoxy treated for outdoor installations. Monitoring optical message flashlighting every 60 s (only 

in win mode). Complies with EN50131-4, environmental class IV, IP43 protection rating, operating temperature: 

-25°C ÷ + 60°C. Dimensions: 277 x 251 x 72 mm. Available in two versions: 

 9510-GOLD-OBLO 

and

 9518-GOLD-

OBLO/L 

with anti-foam, anti-flame, WIN supply.

9557-GOLD-OUT

The wireless output module extends the functions of the GOLD system and has a relay output that can be piloted 

from the control panel or dialer for “Apply”tions, such as: activate camera recording (videoverification), control an 

electric lock, perform automated tasks, such as turn an electrical appliance on and off (together with an external relay, 

not supplied). The wireless output can be associated with a detector to be activated when an intrusion is detected. 

It also has the AND mode to be activated only when the intrusion has been detected by at least two detectors. The 

wireless output module also has a usable input, for example, to verify that the load has been activated.

9560-GOLD-PRIME

Outdoor wireless siren with optical and acoustic signals, protected against opening and wall removal. Made of ABS, 

it is powered by a 6 V battery that conforms to EN50131-4, environmental class IV, IP43 protection rating, operating 

temperature: -25°C ÷ + 60°C. 

B

A

C

Fig. 1 

1.3  PACKAGE CONTENT

The contents of the package are shown below:

Table 1

Part

Description

A

Device

B

Product manual

C

Pendrive containing the programming software

1.2 ACCESSORIES

Below is a list of accessories compatible with the transceiver:

9589-GOLD-TXRX-S

Expansion module that allows you to add 8 wired outputs in addition to those already on board. It is possible 

to connect up to a maximum of 3 expansions up to a maximum of 32 outputs and as many memorable radio 

devices.

Summary of Contents for ZENITH GOLD 869 Series





















Reviews: