background image

IS431  ECN3592 

15 

 

 

 

 

Gas  catering  equipment  should  be  routinely  serviced  to  ensure  a  long  trouble  free  life.  It  is 
recommended that this appliance is serviced every 6 months by a competent gas engineer. 
For help regarding the installation, maintenance and use of your LINCAT equipment, please call:- 

 
 
 

 
 

LINCAT SERVICE HELP DESK 

 

 

+44 (0) 1522 875520 

 
 
 
 

 

AUTHORISED SERVICE AGENTS

 

All service work, other than routine cleaning, to be carried out by our authorised agent. 
 We cannot accept responsibility for work carried out by other persons.   
 
Please quote both the model and serial numbers from the data plate attached to the unit.  Give brief 
details of the service requirement. 
 
 
If possible please quote the product code of the part number you require. 
 
Work carried out under warranty will normally be undertaken only during normal working hours, i.e. 
Monday to Friday, 8.30 a.m. - 5.00 p.m. 
 

CONDITIONS OF GUARANTEE 
 

The guarantee does not cover:- 
 
1) 

Accidental breakage or damage 

2) 

Operational misuse, wear and tear from normal usage, incorrect adjustment, or neglect. 

3) 

Incorrect installation, maintenance, modification or unauthorised service work. 

 

  

SERVICE INFORMATION

 

Summary of Contents for OG7001
















Reviews: