manualshive.com logo in svg

LIMBACH L 2000 DA, Operating And Maintenance Manual

Share
Download
LIMBACH L 2000 DA Operating And Maintenance Manual Download Page 48

 

 

 

Page: 48/48 

Operating Manual L 2000 

Edition: 01.03.2016 

201

.2

5

3

.9

0

5

.0

0

0

 

12.3  Mechanical System 

 

 

Possible Cause: 

 

Remedy:

 

No valve clearance.

 

Set valve clearance.

 

 

 

Leaking or sticking valve.

 

Repair cylinder head. 

 

Note: 

In some cases, fuel tanks made out of com-
posite materials have been proven to be in-
compatible with the fuel, thus causing the 
tank material to dissolve. In such cases, the 
complete fuel system must be cleaned or 
even be re placed.

 

 

 

Strong accumulation of deposit in the 
combustion chamber.

 

Demount cylinder heads, remove deposits.

 

 

 

Propeller unbalance.

 

Balance propeller. Check propeller blade 
track.

 

 

 

Engine suspension defective.

 

Replace engine suspension.

 

 

 

Excessive gas leakage at the piston.

 

Repair engine.

 

 

 

Bearing defective.

 

Repair engine.

 

 

 

Engine defective.

 

Repair engine.

 

 

Summary of Contents for L 2000 DA

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands