LIMBACH L 2000 DA Operating And Maintenance Manual Download Page 14

Page: 14 / 48

Page: 14/48

Operating Manual L 2000

Edition: 01.03.2016

201

Engine Ratings

Max. Take-Off Power

59 kW / 80 shp @ 3400 RPM

Max. Continuous Power

53 kW / 72 shp @ 3000 RPM

Engine Rotational Speeds

Max. permissible speed

3400 RPM

Max. speed for cruise

See flight and maintainance manual
of airframe manufacturer.

Min. continuous speed

2300 RPM

Idle speed

800 ± 100 RPM

Fuel and Oil

Fuel

see section 10

Engine Oil

see section 10

Pressures and Temperatures

Fuel Pressure

0.1 to 0.15 bar / 1.45 to 2.17 psi

Engine Oil Pressure max.

4 bar / 58 psi

Engine Oil Pressure

min.

1 bar / 14.5 psi @ 2500 RPM

Engine Oil Temperature max.*)

120 °C

Engine Oil Temperature

min

50 °C (indicated)

Engine Oil Temperature

opt.

appr. 80 °C

Cylinder Head Temperature max.*)

250 °C

Cylinder Head Temperature

opt.

150 to 170 °C (at cruise)

Oil Charge

Engine Oil Charge max.

2.5 l

Engine Oil Charge

min.

1.5 l

*) The max. permissible temperatures constitute operating limitations to be maintained for a short

period of time only. Continuous operation of the engine at these temperatures may impair engine life

Summary of Contents for L 2000 DA

















































Search results

Summary of Contents for L 2000 DA

Reviews:

Brands by name

Popular brands

LIMBACH L 2000 DA, Operating And Maintenance Manual

Search results

Summary of Contents for L 2000 DA

Reviews:

Brands by name

Popular brands