manualshive.com logo in svg

Lightware HDMI-3D-OPT-RX150RA, User Manual

Share
Download
Lightware HDMI-3D-OPT-RX150RA User Manual Download Page 84

 

9. Troubleshooting 

HDMI-3D-OPT series – User's Manual 

84

Symptom

Root cause

Action

Refer to

Audio signal

No audio is 

present on output

Source audio volume is 

low or muted

Check the audio settings of the source.

Audio input port is 

muted

Check the audio input port properties

5.4.2
5.4.3

LW3

7.7.1

Audio output port is 

muted

Check the output port properties.

5.4.5

LW2

6.3.6

LW3

7.7.2

Analog audio input: 

volume is set very low 

(TX)

Check the Analog audio input port 

settings (Volume).

5.4.3

LW3

7.7.17

LW3

7.7.18

Analog audio output: 

volume is set very low 

(RX)

Check the Analog audio output port 

settings (Volume).

5.4.6

LW3

7.7.19

LW3

7.7.20

HDMI output 

signal contains no 

audio

HDMI mode was set to 

DVI

Check the properties of the output port 

and set the signal type to HDMI or Auto.

5.4.4

LW3

7.6.20

DVI EDID is emulated

Check the EDID and select and HDMI 

EDID to emulate.

5.7

LW3

7.12

RS-232 signal

Connected serial 

device does not 

respond

Cable connection 

problem

Check  the  connectors  to  fit  well;  check 

the wiring of the plugs.

3.4.9
3.4.10

RS-232 settings are 

different

Check the port settings of the extender 

and the connected serial device(s).

5.8.1

LW3

7.9

RS-232 mode is not right Check the RS-232 mode settings (control, 

pass-through, or command injection)

5.8.1

LW3

7.9.6

Symptom

Root cause

Action

Refer to

Ethernet (only for SW4-OPT-TX240RAK)

No LAN 

connection can be 

established

Incorrect IP address is 

set (fix IP)

Use dynamic IP address by enabling 

DHCP option.

4.3.1

5.10.2

LW3

7.8.2

Restore the factory default settings (with 

fix IP).

4.3.2

5.10.4

LW2

6.2.11

LW3

7.5.6

IP address conflict

Check the IP address of the other 

devices, too.

USB KVM

USB device does 

not operate

Cables are not 

connected on both sides

Check the USB cable between TX and the 

computer.

Not supported USB 

device is connected

Keyboard, mouse (USB HID devices) are 

supported mostly, check your device 

type

USB crosspoint set to 

the non-active channel

Check the USB mode in the transmitter 

in LDC and change to the active channel.

5.6.2

Incorrect USB mode is 

set

Check the USB mode in the receiver 

in LDC and change to Composite or 

Transparent mode.

5.6.1

GPIO

Connected device 

does not respond

Cable connection 

problem

Check  the  connectors  to  fit  well;  check 

the wiring of the plugs.

3.4.14

Output level 

cannot be changed

The direction of the 

selected pin is set to 

input

Check and modify the direction setting 

of the desired pin

5.8.2

LW2

6.5.1

LW3

7.11

Miscellaneous

Front panel 

buttons are out of 

operation

Buttons are locked

Unlock the buttons

4.3.3

Error messages 

received 

continously

Different protocol is set

Check  the  port  protocol  settings  (LW2 

/  LW3)  and  use  the  proper  protocol 

commands.

5.8.1

LW3

7.9.1

 

Summary of Contents for HDMI-3D-OPT-RX150RA


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands