background image

Lightning Protection International Pty Ltd

ABN 11 099 190 897

PO Box 379 Kingston, Tasmania, Australia 7051

Phone: 

+61 3 62271955

Fax: 

+61 3 62291900

Email: 

 [email protected]

Web: 

 www.lpi.com.au

STORMASTER ESE INSTALLATION MANUAL

As a result of continuing research and product development in the area of lightning and 
lightning protection, LPI reserves the right to alter any detail contained within at any 
time without notice.
Prior to installation of the Stormaster ESE system, installers should check with LPI or an 
authorised distributor to confirm they have the most recent version of the Stormaster 
ESE Installation manual. 

 

 

 

It should be noted that 100% (100 percent) protection level for direct lightning strikes 
is not possible and cannot be provided due to the lightning discharge process being a 
natural atmospheric event.

Stormaster ESE Lightning Protection System

System Owner:_____________________________________________________

Date Installed:_____________________________________________________

Installation Contractor:______________________________________________

Supplied by:_______________________________________________________

Location of Installation

:____________________________________

________

Summary of Contents for Stormaster 15





















































Reviews: