background image

LIGHT PROGRESS

 

FLOW-C-NX [Eng.]

 

Rev. 2 Oct -2020 

Pag. 4/16

 

 

 
 

 

 

CONVENTIONAL SYMBOLS

 

 

DISPOSE THIS PRODUCT ON THE UNDIFFERENTIATED WASTE DISPOSING OF THE 

SUBSTITUTED ITEMS MUST BE PERFORMED RESPECTING THE LOCAL LAWS. 

 

 

       

RECYCLE THE STUFFS THAT COMPOSES THIS PRODUCT. 

 

     

 

OBLIGATION TO CONSULT THESE INSTRUCTIONS BEFORE USE THIS PRODUCT 

 

 

 

DANGER OF ELECTRICAL SHOCK; REMOVE TENSION TO THE SYSTEM BEFORE PERFORMING 

ANY OPERATION. 

 
 

 

GENERIC DANGER. 

 

     

DANGER OF EXPOSITION TO ULTRAVIOLET UV-C RAYS.  

      

 

 

THIS DEVICE RESPECTS THE ROHS NORMS. 

 
 
 
 

    

USE PROTECTIVE GLOVES 

    

WEAR PROTECTIVE GLASSES 

 

 

MANUAL

 

 

ATTENTION!

 

 

 
 

This instruction manual must be preserved and must always be kept available for consultation; it must follow 

the device in case of transfer of ownership and accompany the device until its disposal.

 

 

DISPOSAL

 

 

Do not dispose of these products as unsorted municipal waste. Collect them separately as a special waste 

and entrust them to specialized waste disposal companies. Disposal should be in accordance with Legislative 

Decree No. 151/2005 (WEEE - Italy), or the law of the country where disposal will occur (WEEE - EC). In case 

of  failure to  comply  with  laws  or  illegal  disposal  heavy  penalties are  provided. The  apparatus consists  of 

plastic  parts,  electronic  components,  metal,  UV  lamps  containing  mercury  (substances  dangerous for the 

environment and human health). The dealer is available to the withdrawal of the apparatus used

Summary of Contents for UV-FLOW C-NX Series



















Reviews:

Related manuals for UV-FLOW C-NX Series