LIGHT MY BRICKS LEGO TRON Legacy 21314 Manual Download Page 3 | Manualshive

Page: 3 / 36

background image

Incorrectly inserting the connector can can

result in bent pins inside the port or possible
overheating of the expansion board when
connected.

Connecting cable connectors to Strip Lights

Take extra care when inserting connectors to ports on the Strip Lights.

Connectors can be inserted only one way. With the Strip Light facing up,
ensure the side of the connector with the wires exposed is facing down. If
a plug won’t t easily into a port connector, don’t force it. Doing so will
damage the plug and the connector.

Installing Bit Lights under LEGO® bricks and plates.

«
1
2
3
4
5
...
»

Summary of Contents for LEGO TRON Legacy 21314





































Reviews:

No comments

Related manuals for LEGO TRON Legacy 21314

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

Brand: ParaBody Pages: 4

Brand: Rath Pages: 3

Brand: Hanil Pages: 60

Brand: UMAGE Pages: 15

Brand: CAB Pages: 13

Brand: CAB Pages: 30

Brand: CAB Pages: 17

Brand: CAB Pages: 33

Camping Equipment

Brand: C. Crane Pages: 8

Brand: C-Pro Direct Pages: 4

Brand: C-Pro Direct Pages: 4

Brand: Warehouse-lighting Pages: 3

Brand: E2S Pages: 5

Brand: Unitary products group Pages: 28

Brand: Fenton Pages: 16

Brand: Keller Pages: 12

Brand: MacDon Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands