LIGHT MY BRICKS LEGO TRON Legacy 21314 Manual Download Page 15 | Manualshive

Page: 15 / 36

background image

8.)

Before reconnecting the front two wheels we need to install a light
to the headlight. First disconnect and disassemble the following
pieces from the front of the vehicle.

Take the remaining Blue 30cm Bit Light and then with the cable facing the

right side (facing up), place it over the black stud. Secure the bit light in
place by reconnecting the trans light blue plate over the top followed by
the black arched piece.

«
...
13
14
15
16
17
...
»

Summary of Contents for LEGO TRON Legacy 21314





































Reviews:

No comments

Related manuals for LEGO TRON Legacy 21314

Brand: Taber Pages: 27

Brand: JB-Lighting Pages: 40

Brand: ZIGBEE Pages: 6

Brand: Daisy Pages: 2

Below Ground Pool Cover Box

Brand: Daisy Pages: 3

Brand: Yamaha Pages: 46

Brand: LA Audio Pages: 9

Brand: Velleman Pages: 16

Brand: Velleman Pages: 11

Brand: Kärcher Pages: 20

Brand: Parker Research Corp Pages: 3

TR 2B INC INT NC

Brand: OMGA Pages: 76

Brand: Meyer Pages: 100

Rovelight RT-400

Brand: Orlit Pages: 16

Brand: Qazqa Pages: 2

Life/form LF03608

Brand: Nasco Healthcare Pages: 6

Brand: Beta Pages: 8

Brand: Furuno Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands