background image

4. Automatic Closing & Time Setting

NOTE: We recommend that Safety Photo Beams are used in any 

installation where the Auto Close function is enabled.

a) 

Press and hold 

SET

 Button until “1”appears on the display, next 

press the 

UP

 button until “4” appears on the display to enter this 

function setting then release the button.

b)

 Press the 

SET

 button again, the unit is now in automatic close 

adjustment mode. You will see a figure “0” with a flashing dot on the 

display.

c)

 Press 

UP / Down

 button once to set the auto close time (0~9).

d)

 Press 

UP

 button to increase the time, or 

DOWN

 button to 

decrease the time.

The close time is 15second*N, N=0~9. 

The maximum time is 135s. To disable Auto Close Function, set 

time to zero (0).

e)

 Press 

SET 

button to confirm the settings and it will return to 

standby status automatically and display “ll”.

NOTE:

  

1.

The closing time is set on “0” as standard.

2.

 If the Photo Cell Function is on, and the light beam is broken by 

the obstruction, the auto close time will stop for a while, and then 

continue the automatic close time again.

SET

UP

C

ODE

DOWN

SET

UP

C

ODE

DOWN

increase time

decrease time

SET

UP

C

ODE

DOWN

SET

UP

C

ODE

DOWN

14

Summary of Contents for LPO0600





























Reviews: