manualshive.com logo in svg

Lifelines trackit T4 32, User Manual, Page: 48 / 50

Share
Download
Lifelines trackit T4 32 User Manual Download Page 48

T4 EEG Amplifier User Manual 

48 

Guidance and Manufacturer’s Declaration 

 

Electromagnetic Emissions 

EN 60601-1-2 

The T4 is intended for use in the electromagnetic environment specified below. The customer or 

user of the T4 should assure that it is used in such an environment. 

 

Emissions Test 

Compliance 

Electromagnetic Environment Guidance 

RF emissions 
CISPR11/EN55011 

Group 1 

The T4 uses RF energy only for its internal function. Therefore, its RF 
emissions are very low and are not likely to cause any interference in 
nearby electronic equipment. 

RF emissions 
CISPR11/EN55011 

Class B 

The T4 is suitable for use in all establishments, including domestic es-
tablishments and those directly connected to the public low voltage 
power supply network that supplies buildings used for domestic pur-
poses. 
Note: Only the recommended or supplied PC must be used in the sys-
tem to ensure compliance. 

Harmonic emissions 
EN 61000-3-2 

Class A 

Voltage fluctuations/Flicker 
emissions EN 61000-3-3 

Complies 

 

Electromagnetic Immunity 

EN 60601-1-2 

The T4 is intended for use in the electromagnetic environment specified below. The customer or 

user of the T4 should assure that it is used in such an environment. 

 

Immunity Test 

EN 60601-1-2 

Test Level 

Compliance Level 

Electromagnetic Environment Guid-

ance 

Electrostatic dis-
charges (ESD) 
EN 61000-4-2 

+/- 6 kV:Contact 
+/- 8 kV:Air 

+/- 6 kV:Contact 
+/- 8 kV:Air 

Floors should be wood, concrete or ceramic 
tile. If floors are covered with synthetic ma-
terial, the relative humidity should be at 
least 30% 

Electrical fast Transi-
ents/burst 
EN 61000-4-4 

Compliance is provided 
by the recommended PC 
equipment. 

Compliance is provided 
by the recommended PC 
equipment. 

Mains power should be that of a typical com-
mercial and/or hospital environment 

Surge 
EN 61000-4-5 

Compliance is provided 
by the recommended PC 
equipment. 

Compliance is provided 
by the recommended PC 
equipment. 

Mains power should be that of a typical com-
mercial and/or hospital environment 

Voltage dips,short in-
terruptions and volt-
age variations on 
power supply input 
lines 
EN 61000-4-11 

Compliance is provided 
by the recommended PC 
equipment. 

Compliance is provided 
by the recommended PC 
equipment. 

Mains power should be that of a typical com-
mercial and/or hospital environment. If the 
user of the T4 requires continued operation 
during power mains interruptions, it is rec-
ommended that the T4 be powered from an 
uninterruptible power supply or a battery 

Power frequency 
(50/60 Hz) magnetic 
field 
EN 61000-4-8 

3 A/m 

3 A/m 

Power frequency magnetic fields should be 
at levels characteristic of a typical location 
in a typical commercial and/or hospital en-
vironment 

 

 

Summary of Contents for trackit T4 32



















































Reviews:

No comments