Lifebreath RNC10 Installation Instructions Manual Download Page 15

15

Drain Connection (HRV Only)

During a defrost cycle, the HRV may produce some
condensation. This water should flow into a nearby drain, or be
taken away by a condensate pump. 

The HRV cabinet has prepunched holes for the drain (see
below). Insert the drain spout through the hole in the drain pan.
Do not forget the “O ring” which seals each spout to the pan
REMEMBER TO HAND TIGHTEN ONLY the washer and
lock nut which hold the drain spout in place.

Construct a P-Trap using the plastic tee connector. Cut two
lengths of hose and connect each piece to an end of the “T”
fitting, then connect the other ends to the two drain spouts.
Position the “T” fitting to point upward and connect the drain
line. Tape or fasten base to avoid any kinks. Pour a cup of water
into the drain pan of the HRV after the drain connection is
complete. This creates a water seal which will prevent odors
from being drawn up the hose and into the fresh air supply of
the HRV.

Drain Connections

Note: Secondary drain pan may be required to
protect from condensate leakage.

Use drain spout provided in 
door. “P” trap must be at least 
6” (152 mm) below unit.

Do not remove
these drain plugs

1/2” I.D.
condensate line

Use “T” between drain pans 
to create a “P Trap”. “P” trap
must be at least 6” (152 mm)
below unit.

Do not remove 
cap from drain spout

1/2” I.D.
condensate line

Drain trap and tubing MUST be below bottom of 
door with 1/4" per foot downwards slope away 
from unit. 

CAUTION

The HRV and all condensate lines must be 
installed in a space where the temperature is 
maintained above the freezing point or freeze 
protection must be provided. 

CAUTION

Drain Set-up for Vertical Installation

Drain Set-up for Horizontal Installation

DRAIN

SPOUT

ZIP  TIE

TO DRAIN

TEE

CONNECTOR

DRAIN

SPOUT

PRE-PUNCHED HOLES (2)

DRAIN PAN

DRAIN PAN

1/2 " I.D. 

DRAIN HOSE

DRAIN HOSE PLUMBING

DRAIN

SPOUT

DRAIN

SPOUT

TO DRAIN

1/2" HARD PIPE

TEE

JOINT

PRE-PUNCHED HOLES (2)

DRAIN PAN

DRAIN PAN

HARD PIPE PLUMBING

"P" Trap (HRV only)

Model RNC120D

Summary of Contents for RNC10





































Reviews: