Lifebreath 1230 ERV Page 3 Installation Manual Download

Page: 3 / 35

www.lifebreath.com

Table of Contents

Functions and Controls ............................................................................................................................................. 12

Main Wall Control ..................................................................................................................................................... 13

Timers and Repeaters ............................................................................................................................................... 18

Aircom Relays & Interlocking to a furnace/air handler ............................................................................................ 22

Balancing the Airflows .............................................................................................................................................. 24

Service and Maintenance .......................................................................................................................................... 26

Reverse Installation of the ERV ................................................................................................................................. 28

Troubleshooting ........................................................................................................................................................ 29

Wiring Diagrams (330ERV) ........................................................................................................................................ 31

Wiring Diagrams (530ERV) ........................................................................................................................................ 32

Wiring Diagrams (730ERV and 1230ERV) .................................................................................................................. 33

Warranty ................................................................................................................................................................... 34

Summary of Contents for 1230 ERV




































Search results

Summary of Contents for 1230 ERV

Reviews:

Related manuals for 1230 ERV

Brands by name

Popular brands

Lifebreath 1230 ERV, Installation Manual

Search results

Summary of Contents for 1230 ERV

Reviews:

Related manuals for 1230 ERV

Brands by name

Popular brands