Life Gear Orbi trac 28320 Owner'S Manual Download

Page: 13 / 27

Install a S18 Nut Cap (67) onto the B0.5x20 Nylon Nut for right Crank (40).

NOTE: Ø16x89xL23 Bolt for right Crank (22) and Ø16x89xL23 Bolt for left Crank (46)
are marked “R” for Right and “L” for Left.

Use the same procedure to attach the left Foot Bar (23) onto the left Crank (41).
Install four S16 Nut Caps (68) onto M10x55 Bolts (25) and M10x9 Nylon Nuts (28) on the
both Foot Bars (23).

Hardware:

(7) Bolt M10x18

2 PCS

(8) Spring Washer

Ø18xØ10x2t

2 PCS

(9) Washer

Ø28xØ16.2x4xB5

2 PCS

(12) Rotation Rod

Ø15.8x376

1 PC

(11) Wave Washer

Ø28xØ16x1.0t

2 PCS

(22) Bolt for right Crank

Ø16x89xL23, 1 PC

(11) Wave Washer

Ø28xØ16x1.0t, 1 PC

(39) Spring Washer

Ø20xØ13x2, 1 PC

(40) Nylon Nut for right

Crank B0.5x20, 1 PC

(46) Bolt for left Crank

Ø16x89xL23, 1 PC

(11) Wave Washer

Ø28xØ16x1.0t, 1 PC

(39) Spring Washer

Ø20xØ13x2, 1 PC

(43) Nylon Nut for left

Crank B0.5x20, 1 PC

(67) Nut Cap S18

2 PCS

(68) Nut Cap S16

4 PCS

Summary of Contents for Orbi trac 28320




























Search results

Summary of Contents for Orbi trac 28320

Reviews:

Related manuals for Orbi trac 28320

Brands by name

Popular brands

Life Gear Orbi trac 28320, Owner'S Manual

Search results

Summary of Contents for Orbi trac 28320

Reviews:

Related manuals for Orbi trac 28320

Brands by name

Popular brands