Life Gear 75112 Owner'S Manual Download | Manualshive

Page: 20 / 26

background image

ADJUSTING THE ANGLE HOLDER

Pull up on the Small Spring Knob (17), slide the Adjustable Instep Frame (6) upward. Stand on the
Foot Bar (39) located at the bottom of the Adjustable Boom (3). Pull up on the Small Spring Knob
(17), allow the Adjustable Instep Frame (6) to slide back into the Adjustable Boom (3). Push in
slightly on the Adjustable Instep Frame (6) until the Rubber Heel Holders (31) are around your
ankles. Release the Small Spring Knob (17) and adjust the Adjustable Instep Frame (6) slightly
until the Small Spring Knob (17) locks into place.

GENERAL PRECAUTIONS

1. Make sure that the Pivot Arms (5) are locks on the lowest hole for the first few attempts.
2. It is recommended that someone be with you while you are using this inversion table for the

first few times.

3. Make sure that the Rubber Heel Holders (31) are holding your feet securely.
4. Make sure that the Adjustable Boom (3) is properly set to your height.
5. Make sure that the Adjustable Boom (3) is held securely by both the Large Spring Knob (18) and

the Knob (30).

6. Make sure that there is enough room for the bed to rotate completely.

19

17

6

3

31

«
...
18
19
20
21
22
...
»

Summary of Contents for 75112



























Reviews:

No comments

Related manuals for 75112

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: Dairyland Pages: 21

Brand: TAIKO Audio Pages: 24

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: b&o Pages: 46

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: Wacker Neuson Pages: 62

Brand: Raymarine Pages: 3

SmartPilot ST8002

Brand: Raymarine Pages: 48

Brand: Raymarine Pages: 38

hsb2 PLUS Series

Brand: Raymarine Pages: 248

Brand: Teac Pages: 76

Brand: Teac Pages: 3

Brand: Teac Pages: 50

Brand: Teagle Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands