Life Fitness T3, Service Manual

Page: 62 / 67

Section 5 7
IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL
NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
1.
Remove the tape securing the MOTOR COVER (A) to the FRAME (B).
Carefully lift and remove the MOTOR COVER.
2.
Remove the USER LEFT UPRIGHT (#1) (with grommets installed) from the
ship kit. With the USER LEFT UPRIGHT angled toward the rear of the unit,
align the mounting holes of the flanged end of the USER LEFT UPRIGHT with
those on the top of the FRAME (B). Using two BOLTS (#10), secure the
USER LEFT UPRIGHT to the FRAME. Tighten the BOLTS using a 9/16”
combination wrench until snug and then back them off 1/4 turn. Repeat the
procedure for the USER RIGHT UPRIGHT (#2).
3.
Locate the DISPLAY CONSOLE ASSEMBLY (#3). Unwrap the WIRE
HARNESS (C) secured to the back of the DISPLAY CONSOLE
ASSEMBLY. Standing at the front of the unit, carefully lower the DISPLAY
CONSOLE ASSEMBLY down near the tops of the USER LEFT and
RIGHT UPRIGHTS (#1 & #2). Lower the user right side of the DISPLAY
CONSOLE ASSEMBLY to rest on the USER RIGHT UPRIGHT. Holding
the user left side of the DISPLAY CONSOLE ASSEMBLY slightly above
the USER LEFT UPRIGHT, feed the WIRE HARNESS down into the
USER LEFT UPRIGHT through the TOP CABLE ROUTING HOLE (D) of
the USER LEFT UPRIGHT. Once the WIRE HARNESS is completely
inserted into the USER LEFT UPRIGHT, lower the DISPLAY CONSOLE
ASSEMBLY to completely rest on the USER LEFT UPRIGHT.
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRE HARNESS (C)
WHEN ROUTING IT THROUGH THE USER LEFT UPRIGHT (#1).
NOTE: BE CAREFUL NOT TO PINCH THE WIRE HARNESS (C)
WHEN LOWERING THE DISPLAY CONSOLE ASSEMBLY (#3) ONTO
THE USER LEFT UPRIGHT (#1).
4.
MODELS T3 AND T3i ONLY (Models T5 and T5i Skip to Step 5)
Locate the HANDRAIL (#11) and one TOP HANDRAIL SPACER (#5).
On the user right side of the HANDRAIL insert a SHORT MOUNTING
BOLT (#6) through the bottom most of the three top mounting holes of
the HANDRAIL. Slide the TOP HANDRAIL SPACER over the SHORT
MOUNTING BOLT as shown until it fully nests over the. Slide the
HANDRAIL with the TOP HANDRAIL SPACER over the user right end
of the display console and upright. Align and insert the SHORT
MOUNTING BOLT into the bottom most mounting holes of the user right
UPRIGHT. Tighten the bolt until snug and. Insert two LONG MOUNTING
BOLTS (#7) through the two remaining mounting holes and tighten all
three bolts securely using a 5/32” hex key wrench. Leave the user left side
of the HANDRAIL unfastened at this time. Continue to
Step 7 .
5.
MODELS T5 AND T5i ONLY Locate a HANDRAIL (#4) and a TOP
HANDRAIL SPACER (#5). Insert a SHORT MOUNTING BOLT (#6)
through the bottom most of the three top mounting holes of the
HANDRAIL. Slide the TOP HANDRAIL SPACER over the SHORT
MOUNTING BOLT as shown until it fully nests over the HANDRAIL Align
and insert the SHORT MOUNTING BOLT into the bottom most mounting
hole of the USER LEFT UPRIGHT (#1). Tighten the bolt until snug and
then back it off one full turn. Insert two LONG MOUNTING BOLTS (#7)
through the two remaining mounting holes and tighten all three bolts
securely using a 5/32” hex key wrench.
Sectio
n V
A
B
1
B
10
3
C
1
D
5
1
4
7
6
5
7
11