background image

LIMITED WARRANTY

Liebert Corporation (hereinafter collectively referred to as THE COMPANY),

warrant for a period of two years from date of shipment, that THE COMPANY’s
manufactured and assembled products, not otherwise expressly warranted (with the
exception of the cylinder) are free from defects in material and workmanship. No
warranty is made against corrosion, deterioration, or suitability of substituted materials
used as a result of compliance with government regulations.

THE COMPANY’s obligations and liabilities under this warranty are limited to

furnishing replacement parts to the customer, F.O.B. THE COMPANY’s factory,
providing the defective part(s) is returned freight prepaid by the customer. Parts used
for repairs are warranted for the balance of the term of the warranty on the original
humidifier or 90 days, whichever is longer.

The warranties set forth herein are in lieu of all other warranties expressed or

implied by law. No liability whatsoever shall be attached to THE COMPANY until said
products have been paid for in full and then said liability shall be limited to the original
purchase price for the product. Any further warranty must be in writing, signed by an
officer of THE COMPANY.

THE COMPANY’s limited warranty on accessories, not of Liebert’s manufacture,

such as controls, humidistats, pumps, etc. is limited to the warranty of the original
equipment manufacturer from date of original shipment of humidifier.

THE COMPANY makes no warranty and assumes no liability unless the

equipment is installed in strict accordance with a copy of the catalog and installation
manual in effect at the date of purchase and by a contractor approved by THE
COMPANY to install such equipment.

THE COMPANY makes no warranty and assumes no liability whatsoever for

consequential damage or damage resulting directly from misapplication, incorrect sizing
or lack of proper maintenance of the equipment.

THE COMPANY retains the right to change the design, specification and

performance criteria of its products without notice or obligation.

Summary of Contents for SGH Steam

















Reviews: