– 4 –
Copyright © Liberty Pumps, Inc. 2018 All rights reserved.
5755000H
Inspection and Storage
Initial Inspection
The Ascent II Macerating Toilet System is shipped in three
separate packages: the toilet tank, toilet bowl, and macerating
unit. The shipping containers should be immediately inspected for
damage that may have occurred in shipment.
1.
Visually check the macerating unit and any spare parts for
damage.
2.
Check for damaged electrical wires, especially where they exit
the macerating tank.
3.
Check all packaging for spare parts before discarding.
Contact Liberty Pumps customer service to report any damage or
shortage of parts.
List of included parts:
•
Toilet Tank (model: Ascent II - TW)
•
Toilet Bowl (model: Ascent II – RW or EW)
•
Macerator (model: Ascent II - MUW)
– Macerator tank
– Rubber couplings with clamps
– Reducing bushings
– 9V battery
– 3/16” Allen wrench
– Grease packet
Storage Before Use
Liberty Pumps products are shipped from the factory ready for
installation and use. If storage is necessary, the pump should
remain in its shipping container. It should be stored in a
warehouse or other area that is clean, dry and temperature-stable.
The pump and packaging should be covered to protect it from
water, dirt and dust.
General Information
The macerator is designed to accept wastewater from a rear
discharge toilet but can also simultaneously receive wastewater
from several sanitary fixtures such as a sink, shower, bathtub, or
urinal (a single bathroom group). However, only one water closet
(toilet) per unit may be connected.
Usage
The macerating system is designed for the disposal of human
waste, toilet paper, and water. It is not intended for kitchen waste,
nor is it intended to be used for the disposal of wastewater from
such pumped appliances as dishwashers and clothes washers. This
product is not designed for emptying large pools or spas.
The macerating system starts automatically once the toilet is
flushed or liquid from other fixtures enters the unit. It
automatically shuts off once the contents have been pumped
away. Run times will vary depending on inflow and source.
Features
•
Improved cutter design with RazorCut™ system. The cutter
blades are designed and rigorously tested to last
indefinitely without need for service or replacement in
ordinary applications.
•
The CleanConnect™ Seal allows the macerator to sit closer
to the toilet.
•
QuickFlip™ discharge and vent connectors allow for
horizontal or vertical pipe connections.
Bath Layout
The toilet works as a conventional flushing toilet and needs no
special maintenance with normal use.
Sanitary fixtures connected to the macerating system must be
located on the same floor level.
Any regular bathtub (up to 100 gallons) or shower can be used.
When installing these fixtures, build a 6 inch high platform for the
fixture to be placed. This provides enough space for a p-trap and
slope toward the macerator auxiliary inlets. When installing a
shower, manufacturers sometimes offer a prefabricated raised
shower base. The actual distance between the p-trap of the
additional fixture and macerator determines the necessary
clearance.
Normal Operating Cycle
The macerator controls are capable of distinguishing between
different modes of operation and optimizes the run time
accordingly.
Advanced run detection will energize the cutters once the unit
detects a flush. In doing so, the cutters are spinning at maximum
speed (rpm) prior to fluid and debris reaching the cutting system.
The unit may pulse during a shower or draining a bathtub because
the macerator can pump at a higher rate than the incoming flow.
Use and Care
All standard cleaners can be used just as with a standard
conventional toilet. The exterior of the macerating unit may be
cleaned with a damp cloth and normal household cleaners. Never
spray or dump water or chemicals directly on the unit.
Ascent II - MUW
(macerating unit)
GREASE
Ascent II - EW
(elongated toilet)
Ascent II - RW
(round front toilet)
Ascent II - TW
(toilet tank)
