manualshive.com logo in svg

LG WD1070FH, Instruction Manual, Page: 10 / 33

Share
Download
LG WD1070FH Instruction Manual Download Page 10

ERROR

SYMPTOM CAUSE

8

9

10

• The electric contact between the connectors

(5 pin, male in the Wire Harness and 5 pin female in the Hall Sensor) is

bad or unstable.

ƒ_

Reconnect or repair the contact in the connector

• The connector (6 pin, male, natural) in the Wire Harness is not

connected to the connector (6 pin, female, natural) of PWB

ASSY(Main) or the electric contact of connectors is bad/unstable.

ƒ_

Reconnect or repair the contact in the connector 

• The electric contact between the connectors 

¡a

6 pin, male in the Wire

Harness and 6 pin female in the controller(Main)

¡b

is bad or unstable.

ƒ_

Reconnect or repair the contact in the connector

• The Wire Harness between Hall Sensor in the MOTOR and PWB

ASSY(Main) is cut(open circuited).

ƒ_

Repair/replace the damaged WIRE HARNESS

• The Hall Sensor is out of order/defective.

ƒ_

Replace the Motor

• The controller(Main) is out of order/defective.

ƒ_

Replace the PWB ASSY(Main)

• PWB ASSY(Main) is out of order

ƒ_

Replace the PWB ASSY(Main)

• Winding in the MOTOR is short-circuited.

ƒ_

Replace the MOTOR

• The Connector(3 pin, male, white) in the Wire Harness is not

connected to the Connector(3 pin, female, white) of MOTOR.

ƒ_

Reconnect or repair the connector

• The electric contact between the connectors

¡a

3 pin, male, white in the

Wire Harness and 6 pin, female, white in the PWB ASSY(Main)

¡b

is bad

or unstable.

ƒ_

Reconnect or repair the contact in the connector

• The Wire Harness between the MOTOR and PWB ASSY(Main) is

cut(open circuited).

ƒ_

Repair the damaged(open-circuited) WIRE HARNESS

• The hall sensor is out of order/defective.

ƒ_

Replace the PWB ASSY(Main)

SENSOR

ERROR

CURRENT

ERROR

LOCK

ERROR

16

Summary of Contents for WD1070FH


































Reviews:

No comments