LG SxS GR-L207MSU Service Manual Download Page 20

Page: 20 / 126

1. Connection of Pipe Connector A and B.

1) Turn off main valve of water pipe.

2) Disconnect water tap from piping by loosening nuts.

3) Connect pipe connector A and B to piping after sealing

the pipe connector with sealing tapes.

4) Connect feed valve to pipe connector A.

5) If there is only one tap water pipe, connect pipe

connector A only and install feed pipe.

2. Water Supply

1) After the installation of feed water, plug the refrigerator

to the earthered wall outlet, press the water dispenser
button for 2 - 3 minutes, and confirm that the water
comes out.

Caution : •

Feed pipe should be connected to cold water
line. If it is connected to hot water line, trouble
may occur.

• Please check rubber packing when connecting

feed pipe.

2) Check leakage at connecting part, then arrange water

tube and locate the refrigerator at its regular place if
there is no leaking.

HOW TO INSTALL REFRIGERATOR

- 20 -

Single Lever Type Faucet
(general)

Feed

Valve

General Type

Feed

Valve

Two Hands Type Faucet

Single Lever Type Faucet (one
hole, tech type and hand spray)

Feed

Valve

Feed

Valve

Pipe Connector B

Hot Water

Pipe Connector A

Feed

Valve

Cold Water

How to wind

Sealing Tapes.

Water Tube

Nut

Summary of Contents for SxS GR-L207MSU































































































































Search results

Summary of Contents for SxS GR-L207MSU

Reviews:

Related manuals for SxS GR-L207MSU

Brands by name

Popular brands

LG SxS GR-L207MSU, Service Manual

Search results

Summary of Contents for SxS GR-L207MSU

Reviews:

Related manuals for SxS GR-L207MSU

Brands by name

Popular brands