LG SxS GR-L207MSU Service Manual Download Page 18

Page: 18 / 126

1. How to Adjust Door Height of Refrigerator

■

Make the refrigerator level first. (If the refrigerator is not installed on the flat floor, the height of freezer and refrigerator
door may not be the same.)

1. If the height of freezer door is lower than that of

refrigerator compartment :

2. If the height of freezer door is higher than that of

refrigerator compartment :

Insert a driver

into the groove

of adjusting screw

and rotate driver in arrow direction (clockwise) until the
refrigerator becomes horizontal.

Insert a driver

into the groove

of adjusting screw

and rotate driver in arrow direction (clockwise) until the
refrigerator becomes horizontal.

Adjusting
Screw

Driver

Height

Difference

Height
Difference

HOW TO INSTALL REFRIGERATOR

- 18 -

Summary of Contents for SxS GR-L207MSU































































































































Search results

Summary of Contents for SxS GR-L207MSU

Reviews:

Related manuals for SxS GR-L207MSU

Brands by name

Popular brands

LG SxS GR-L207MSU, Service Manual

Search results

Summary of Contents for SxS GR-L207MSU

Reviews:

Related manuals for SxS GR-L207MSU

Brands by name

Popular brands