background image

8-2-8 Temperature Compensation & Overcooling/Undercooling Compensation Circuit

1. Refrigerator Temperature Compensation

2. The temperature compensation for refrigerator compartment is in the following table:

NOTE

: This circuit is designed to input the necessary temperature compensation values into the MICOM. This adjusts the

refrigerator temperature, which is different in each model.

- 35

 

-

Refrigerator

Resistance

Temperature 

Remark

(RCR)

Compensation

180 K

+2.5°C

Compensation by

56 K

+2.0°C

raising the 

33 K

+1.5°C

temperature

18 K

+1.0°C

12 K

+0.5°C

10 K

0 °C

Standard Temperature

8.2 K

-0.5°C

Compensation by

5.6 K

-1.0°C

lowering the

3.3 K

-1.5°C

temperature

2 K

-2.0°C

470 

-2.5°C

Revised resistance

470

2k

3.3k

5.6k

8.2k

10k

12k

18k

33k

56k

180k

Present resistance

No

0.5°C

1°C

1.5°C

2°C

2.5°C

3°C

3.5°C

4°C

4.5°C

5°C

470

change

Up

Up

Up

Up

Up

Up

Up

Up

Up

Up

0.5°C

No

0.5°C

1°C

1.5°C

2°C

2.5°C

3°C

3.5°C

4°C

4.5°C

2k

Down Change

Up

Up

Up

Up

Up

Up

Up

Up

Up

1°C

0.5°C

No

0.5°C

1°C

1.5°C

2°C

2.5°C

3°C

3.5°C

4°C

3.3k

Down

Down

Change

Up

Up

Up

Up

Up

Up

Up

Up

1.5°C

1°C

0.5°C

No

0.5°C

1°C

1.5°C

2°C

2.5°C

3°C

3.5°C

5.6k

Down

Down

Down

Change

Up

Up

Up

Up

Up

Up

Up

2°C

1.5°C

1°C

0.5°

No

0.5°C

1°C

1.5°C

2°C

2.5°C

3°C

8.2k

Down

Down

Down

Down

Change

Up

Up

Up

Up

Up

Up

Refrigerator

2.5°C

2°C

1.5°C

1°C

0.5°C

No

0.5°C

1°C

1.5°C

2°C

2.5°C

(RCR)

10k

Down

Down

Down

Down

Down Change

Up

Up

Up

Up

Up

3°C

2.5°C

2°C

1.5°C

1°C

0.5°C

No

0.5°C

1°C

1.5°C

2°C

12k

Down

Down

Down

Down

Down

Down

Change

Up

Up

Up

Up

3.5°C

3°C

2.5°C

2°C

1.5°C

1°C

0.5°C

No

0.5°C

1°C

1.5°C

18k

Down

Down

Down

Down

Down

Down

Down Change

Up

Up

Up

4°C

3.5°C

3°C

2.5°C

2°C

1.5°C

1°C

0.5°C

No

0.5°C

1°C

33k

Down

Down

Down

Down

Down

Down

Down

Down

Change

Up

Up

4.5°C

4°C

3.5°C

3°C

2.5°C

2°C

1.5°C

1°C

0.5°C

No

0.5°C

56k

Down

Down

Down

Down

Down

Down

Down

Down

Down

Change

Up

5°C

4.5°C

4°C

3.5°C

3°C

2.5°C

2°C

1.5°C

1°C

0.5°C

No

180k

Down

Down

Down

Down

Down

Down

Down

Down

Down

Down

Change

Table of Temperature Compensation by adjusting the
resistance (difference from the current temperature)
e.g., If the refrigerator compensation resistance
(RCR) is changed from 10K (the current resistance)
to 18K (the adjustment resistance), the temperature
of the refrigerator rises 33.8¡F(+1¡C).

Summary of Contents for REFRIGERATOR






































































Reviews: