LG REFRIGERATOR Service Manual Download

Page: 21 / 69

7-1 OPERATION PRINCIPLE
7-1-1 Operation Principle of Icemaker

1. Turning the Icemaker stop switch off (O) stops the icemaking function.
2. Setting the Icemaker switch to OFF and then turning it back on will reset the icemaker control.

Start Position

Icemaking

Mode

Harvest

Mode

Park Position

Fill

•

Test Mode

Waits until water becomes cold after starting the

Icemaking operation.

• Runs MOTOR to drop ice from the tray into the ICE BIN.

• Performs

Icemaking Mode

after supplying water by operating

the SOLENOID in ICE VALVE.

• To operate LINE and SERVICE, press and hold the Cube Size button

for 3 seconds. The icemaking will run through 3 stages:

Harvest Fill Icemaking

• With the detect lever, checks if the ICE BIN is full.

Power (On/Off) Switch

Power On

Adjusts Ejector to

Start Position

with power on.

Cube Size button

ICE MAKER: 3 STEPS

- 21 -

Summary of Contents for REFRIGERATOR






































































Search results

Summary of Contents for REFRIGERATOR

Reviews:

Related manuals for REFRIGERATOR

Brands by name

Popular brands

LG REFRIGERATOR, Service Manual

Search results

Summary of Contents for REFRIGERATOR

Reviews:

Related manuals for REFRIGERATOR

Brands by name

Popular brands