LG RCT689H Service Manual Download Page 105 | Manualshive

Page: 105 / 165

background image

4-18

Fig. C-5-4

1KHz

A: Maximum

7KHz

B: Minimum

Left

Right

Grove of Base A/C

Fig. C-6

X-distance Adjusting Hole

Tilt Adjusting Screw (C)

Fixing Screw

Height Adjusting
Screw (B)

RF ENVELOPE OUTPUT POINT

HEAD RF SWITCHING OUTPUT POINT

OSCILLOSCOPE

Connection Diagram

CH-2

CH-1

Azimuth

Adjustment

Screw(A)

DECK MECHANISM ADJUSTMENT

5-2. Tape Path Check between Pinch Roller and
Take up Guide (Check in the Rev Mode)

1) Check the tape pass status between the pinch roller and

the take-up guide.(Check if there is crumpling of the tape
pass and folding of the take-up guide.)

(1)

When holding of the take-up guide bottom occurs
Turn the tilt adjusting screw (C) clockwise and move
the tape to ensure there is no crumbling or folding of
the tape.

(2)

When holding of the take-up guide top occurs Turn the
tilt adjusting screw (C) counter-clockwise and move

the tape to ensure there is no crumbling or folding of
the tape.

2) Check if there is folding of the tape at the bottom or top

of the take-up guide in cutting-off the REV mode

If the RF waveform is changed after adjusting the A/C
head,
perform fine adjustment to ensure the RF waveform is flat-
tened.

CAUTIONS

5-3. Fine Adjustment (Azimuth Adjustment)

Fixtures and tools used

Connection position

VCR (VCP) status

Adjustment position

• Oscilloscope

• Audio Output Jack

• Play the standard test

• Azimuth Adjusting

• Standard test tape

• Tape, 1KHz, 7KHz.

Screw (A)

(only for SP)

• Height Adjusting Screw

• Driver (+) Type ø 4

(B)

Adjustment Procedure

1) Connect the probe of Oscilloscope to the audio output

jack.

2) Ensure that Audio 1KHz, 7KHz output is flattened at the

maximization point by adjusting the Azimuth adjusting
screw (A).

6. X-distance Adjustment

Fixtures and tools used

Connection position

VCR (VCP) status

Adjustment position

• Oscilloscope

• CH-1: PB RF Envelope • Play the standard test

• Standard test tape

• CH-2: NTSC ; SW 30Hz tape.

(only for SP)

PAL:SW 25Hz

• Driver (+) Type ø 4

• Head switching output

point

• RF Envelope output

point

Adjustment Procedure

1) After releasing the auto tracking, lightly turn the fixing

screw. Turn the (+) type driver (ø 3 ~ ø 4) on the
X-distance adjusting hole to the right or left. Adjust the
RF envelope level to the maximum point and then fix
the fixing screws.

2) For the 31mm head, adjust it with the SP tape recorded

in the width of 31mm since the head travels on the tape
track only for SP with the width of 58mm.

Purpose of adjustment: To maintain compatibility with other VCR (VCP).

«
...
103
104
105
106
107
...
»

Summary of Contents for RCT689H






































































































































































Reviews:

No comments

Related manuals for RCT689H

Brand: Xtreamer Pages: 2

Brand: Tivoli Audio Pages: 253

Brand: Hyundai Pages: 26

Brand: Denon Pages: 147

Brand: Magnavox Pages: 2

Brand: Datavideo Pages: 52

Brand: Luxibel Pages: 14

Brand: Harman Kardon Pages: 69

Brand: Denon Pages: 65

RAC 02 + Media Player

Brand: IC Audio Pages: 72

Brand: Codonics Pages: 31

Brand: Craig Pages: 26

Brand: LG Pages: 16

DN788 - DVD Player

Brand: LG Pages: 2

Brand: LG Pages: 23

DN798 - DVD Player

Brand: LG Pages: 2

Brand: LG Pages: 14

DN191H - HDMI DVD Player

Brand: LG Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands