LG PBACNBTR0 Installation Manual Download Page 20 | Manualshive

Page: 20 / 24

LG PBACNBTR0 Installation Manual Download Page 20

20

LG MultiSITE

TM

Communications Manager

Due to our policy of continuous product innovation, some specifications may change without notification.

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Prerequisite for power up

Ensure power and ground wiring to the controller is ready. See “Earth ground and power”. See Figure 10 for the location of status LEDs.

Steps

1. Apply power. To do this, do one of the following:

• Insert the 2-position 24V power connector plug, or
• Insert the barrel plug of the wall-mount AC adapter (Model Number: ZHWPWADTR).

2. Check the STAT (Status) and BEAT (Heartbeat) LEDs.
When power is applied, after 3-10 sec, the green “STAT” LED illuminates, indicating that the system is OK, with power applied. During

bootup, the “BEAT” LED may blink at 1 Hz with a 90%/10% on/off duty cycle, or in some other irregular pattern. When bootup completes, the

normal 1 Hz “BEAT” LED flash at 50%/50% on/off duty cycle returns.
If after applying power, the “STAT” LED goes out, or if the “BEAT” LED comes on (steady) and stays lit over 2 minutes, contact Technical

Support for assistance.

POWER UP AND INITIAL CHECKOUT

«
...
18
19
20
21
22
...
»

Summary of Contents for PBACNBTR0

























Reviews:

No comments