LG PAHCMS000 Installation Manual Download Page 49

Page: 49 / 60

Installation

Due to our policy of continuous product innovation, some specifications may change without notification.

EEV KIT INSTALLATION

Preparing the Pipes

A. Inlet Pipes from the Air

Source / Water-Source Unit.

B. Outlet pipes to AHU

Evaporator Coil.

C. Pipe Support Bracket.

D. Pipe Insulation.

E. EEV Assembly.

F. 1/2 Inch O.D. Field Piping

(Inlet / Outlet).

C (Two

[2])

Preparing the Pipes

PRLK048A0 and PRLK096A0

1. Unscrew the four (4) M4 screws and detach the two (2) EEV As-

sembly pipe support brackets.

2. Remove the EEV Assembly; remove the pipe insulation from the

EEV Assembly.

3. If cutting pipe, refer to the cutting instructions on the next page.
4. Braze the field-supplied inlet / outlet piping to the EEV Assembly.

See next page for brazing instructions.

Figure 22: PRLK048A0 and PRLK096A0 EEV Kits.

PRLK396A0 / PRLK594A0

1 Check the inlet/outlet pipe before brazing the EEV KIT.

AHU side

Outdoor

unit side

Air-conditioning

standard refrigerant

ﬂ

3 Braze the connector pipe (not provided) at the outdoor unit.

4 When connecting the outdoor unit's connector pipe and the EEV KIT pipe, be sure to use a

socket (not provided) that meets the necessary specifications.

5 As the size of the EEV KIT pipe and the outdoor unit's connector pipe could vary, check the

sizes beforehand and use a socket that meets the necessary specifications.

6 When brazing, make sure to follow safety precautions at all times.

7 Be sure to insulate pipe A after welding with insulation (15T or more).

Notes:

Be sure to pass nitrogen through when brazing. Failure to do so could cause the compressor

to not function properly or become damaged.

It is essential that the pipe is wrapped with a wet towel before and after brazing. Failure

to do so could result in equipment damage.

Use a protective panel or be especially cautious not to let welding sparks come in contact

with the AHU panel.

After brazing, be sure to test for leakage.

Failure to properly insulate the pipe after welding may result in leakage.

Outdoor unit

connector pipe

(not included)

Connector socket

(not included)

AHU and Outdoor

Unit Connection

AHU Connection

2 If cutting pipe, refer to the cutting instructions on the next page.

Outlet

Inlet

Connector

socket (elbow)

(not included)

Summary of Contents for PAHCMS000





























































Search results

Summary of Contents for PAHCMS000

Reviews:

Related manuals for PAHCMS000

Brands by name

Popular brands

LG PAHCMS000, Installation Manual

Search results

Summary of Contents for PAHCMS000

Reviews:

Related manuals for PAHCMS000

Brands by name

Popular brands