LG Multi V Service Manual Download Page 98

Page: 98 / 147

1. Check alien substance in the Fan.
2. Check the imprisonment of fan

Please turn Fan, if fan is turn, ok.

3. Check Motor Wire connection
(Motor

Motor PCB

Inverter or Main PCB)

4. Check the Motor. Refer to the below.

■

How to check the outdoor fan motor of BLDC

Tester

Normal resistance (±10%)

45 Ω

ڡڥ

Checking Outdoor Fan Lock

Motor Wire Connection

Motor1

Inverter PCB

Motor PCB

Motor2

Checking Method for Key Components

- 98 -

2.8 Temperature Sensor

1) Outdoor temperature sensor : TH1

2) Discharge pipe(D-pipe) temperature sensor : TH2

1. Check the condition of installation and the contact of temperature sensor.
2. Check whether the connector contact of temperature sensor is normal.
3. Measure the resistance of temperature sensor.

3) Pipe temperature sensor : TH3

TH1

TH2

TH3

Resistance

10 kΩ±1 %(25 °C)

200 kΩ±1 %(25 °C)

5 kΩ±1 %(25 °C)

1.07 kΩ±3.3 %(85 °C)

28 kΩ±7.7 %(85 °C)

535 Ω±3.3 %(85 °C)

2.9 Fan lock and Fan IPM Check

Summary of Contents for Multi V














































































































































Search results

Summary of Contents for Multi V

Reviews:

LG Multi V, Service Manual, Page: 98 / 147

Search results

Summary of Contents for Multi V

Reviews: