background image

IMPORTANT SAFETY INSTRUCTIONS

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid
dangerous situations and ensure peak performance of your
product

WARNING

It can result in serious injury or death when the directions are
ignored

CAUTION

It can result in minor injury or product damage when the
directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result

in hazards to you and others.

• The information contained in the manual is intended for use

by a qualified service technician familiar with safety
procedures and equipped with the proper tools and test
instruments.

• Failure to carefully read and follow all instructions in this

manual can result in equipment malfunction, property
damage, personal injury and/or death.

WARNING

• Have all electric work done by a licensed electrician according

to "Electric Facility Engineering Standard" and "Interior Wire
Regulations" and the instructions given in this manual and
always use a special circuit.
- If the power source capacity is inadequate or electric work is

performed improperly, electric shock or fire may result.

• Ask the dealer or an authorized technician to install the HR

unit.
- Improper installation by the user may result in water

!

!

!

!

Summary of Contents for Multi V PRHR023





























Reviews: