48
MUL
TI V Ceiling Cassette Indoor Units
Due to our policy of continuous product innovation, some specifications may change without notification.
©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.
Terminal Connections
LG uses a “JIS” type of screw for all terminals; use a JIS screwdriver to tighten and
loosen these screws and
avoid damaging the terminal.
Do not overtighten the
connections — overtightening will damage the terminals — but firmly and securely at-
tach the wiring in a way to prevent external forces from being imparted to the terminal
block.
•
7KHWHUPLQDOVODEHOHG³*1'´DUH127JURXQGWHUPLQDOV7KHWHUPLQDOVODEHOHG
$5(JURXQGWHUPLQDOV
•
3RODULW\PDWWHUV$OZD\VFRQQHFW³$´WR³$´DQG³%´WR³%´
•
$OZD\VFUHDWHDZLULQJGLDJUDPWKDWFRQWDLQVWKHH[DFWVHTXHQFHLQZKLFKDOOWKHLQGRRUXQLWVDQGKHDWUHFRYHU\XQLWVDUHZLUHGLQUHODWLRQ
WRWKHRXWGRRUXQLW
•
'RQRWLQFOXGHVSOLFHVRUZLUHQXWVLQWKHFRPPXQLFDWLRQFDEOH
Figure 53: JIS Screws.
•
1HYHUDSSO\OLQHYROWDJHSRZHUWRWKHFRPPXQLFDWLRQVFDEOHWHUPLQDOEORFN,IFRQWDFWLVPDGHWKH3&%VZLOOEHGDPDJHG
•
$OZD\VLQFOXGHVRPHDOORZDQFHLQWKHZLULQJOHQJWKZKHQWHUPLQDWLQJ)LUPO\DWWDFKWKHZLULQJRUFDEOHEXWSURYLGHVRPHVODFNWRIDFLOLWDWH
UHPRYLQJWKHHOHFWULFDOSDQHOVZKLOHVHUYLFLQJDQGWRSUHYHQWH[WHUQDOIRUFHVIURPGDPDJLQJWKHWHUPLQDOEORFN
:Copper Wire
Terminate multiple power wires of
the same gauge to both sides.
Do not terminate two wires on
one side.
Do not terminate different gauge
wires to a terminal block.
3RZHU:LULQJ&RPPXQLFDWLRQ&DEOH&RQQHFWLRQV
Best practice dictates using solderless ring or fork terminals at all power wiring and communica-
tion cable terminations. Use copper bearing ring or fork terminals;
do not use galvanized or
nickle plate over steel. Use appropriate crimping tool to attach the ring or fork terminals at all
power wiring and control cable terminations. To install:
• Firmly attach the wire; secure in a way to prevent external forces from being imparted to the
terminal block.
• Use an appropriately sized screwdriver for tightening the terminals.
•
Do not overtighten the connections; overtightening will damage the terminals.
If ring terminals or fork terminals are not available, then:
•
Do not terminate different gauge wires to the power terminal block. (Slack in the wiring will generate heat.)
• When terminating wires of the same thickness, follow the instructions demonstrated in the figures below.
,ISRZHUZLUHVDUHQRWSURSHUO\WHUPLQDWHGDQG¿UPO\DWWDFKHGWKHUHLVULVNRI¿UHHOHFWULFVKRFNDQGSK\VLFDOLQMXU\RUGHDWK
Ring Terminal
Wiring / Cable
Figure 51: Close up of a Typical Ring
Terminal.
Figure 52: Proper and Improper Power Wiring Connections.
WARNING
WIRING
3RZHU:LULQJ&RPPXQLFDWLRQ&DEOH&RQQHFWLRQV