background image

IMPORTANT SAFETY INSTRUCTIONS

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLI-
ANCE.

Always comply with the following precautions to avoid danger-
ous situations and ensure peak performance of your product

WARNING

It can result in serious injury or death when the directions are ig-
nored

CAUTION

It can result in minor injury or product damage when the direc-
tions are ignored

WARNING

• Installation or repairs made by unqualified persons can result

in hazards to you and others.

• Installation MUST conform with local building codes.

• The information contained in the manual is intended for use

by a qualified service technician familiar with safety proce-
dures and equipped with the proper tools and test instru-
ments.

• Failure to carefully read and follow all instructions in this man-

ual can result in equipment malfunction, property damage,
personal injury and/or death.

Installation

• Don’t use a power cord, a plug or a loose socket which is

damaged.
- Otherwise, it may cause a fire or electrical shock.

• For electrical work, contact the dealer, seller, a qualified elec-

trician, or an Authorized Service Center.

!

!

!

Summary of Contents for MS05SQ




















Reviews: