LG MS-2642FB Service Manual Download Page 25 | Manualshive

Page: 25 / 35

background image

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Normal

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and
check continuity
of relay 2.
(Operate the unit)

Check high vol-
tage transformer

Output is full power
when you set lower
power level.

Abnormal.

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Normal

Check high vol-
tage capacitor.

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Normal

Check high vol-
tage diode.

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.

(Display operates properly)

NOTE : • Make sure the wire leads are in the correct position.

• When removing the wire leads from the parts, be sure to grasp the connector, not the wires.
• When removing the magnetron, be sure to install the magnetron gasket in the correct position

and in good condition.

«
...
23
24
25
26
27
...
»

Summary of Contents for MS-2642FB




































Reviews:

No comments

Related manuals for MS-2642FB

Brand: F.Bertazzoni Pages: 76

Brand: F.BLUMLEIN Pages: 54

Profile JE2160BF

Brand: GE Pages: 2

Brand: Ignis Pages: 50

Brand: Daewoo Pages: 39

Brand: Mugnaini Pages: 20

Combair EasyCook V200 21036

Brand: V-ZUG Pages: 12

Superdeck Y600 Series

Brand: Bakers Pride Pages: 44

Brand: Hotpoint Pages: 20

Brand: Daewoo Pages: 30

Combair V4000 45

Brand: V-ZUG Pages: 68

Brand: GE Pages: 36

Brand: Daewoo Pages: 32

Brand: Oursson Pages: 72

Brand: Jenn-Air Pages: 36

Advantium PSB9240BL

Brand: GE Pages: 32

BO 470/471 2 Series

Brand: Gaggenau Pages: 60

Brand: Prima Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands