LG MS-1071MC Service Manual Download Page 4

Page: 4 / 36

1-1

This microwave oven is designed for household use only.

It is not recommended for commercial purposes.

ITEM

MODEL

Power Requirement

Power Output

Microwave Frequency

Magnetron

Timer

Outside Dimensions

Cavity Dimensions

Net Weight

Shipping weight

Control Complement

Nameplate Location

Accessories

DESCRIPTION

MS-1071MC

120 Volts AC 60 Hz

MICROWAVE........................... 1,300 Watts (12A)

Single phase, 3 wire grounded

900 Watts full microwave power (IEC705)

2,450 MHz

2M214-39

0 ~ 99 min. 99 sec.

530mm (W) x 314mm (H) x 390mm (D)

349mm (W) x 228mm (H) x 349mm (D)

14.9 Kg (approx.)

16.7 Kg (approx.)

Touch Control System

Clock : 1:00 - 12:59

Microwave Power for Variable Cooking

Power level

HIGH - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Full power throughout the cooking time

9 (Saute) - - - - - - approx. 90% of Full power, 8 (Reheat) - - - - - - - - approx. 80%

7 (Med.-High) - - - - - - - - - - - - - - approx. 70%, 6 (Medium) - - - - - - - - approx. 60%

5 (Med.-Low) - - - - - - - - - - - - - - - approx. 50%, 4 (Defrost) - - - - - - - - - approx. 40%

3 (Low) - - - - - - - - - - - - - - - - - - - - approx. 30%, 2 (Simmer) - - - - - - - - - approx. 20%

1 (Warm) - - - - - - - - - - - - - - - - - - approx. 10%

Owner's manual & cooking guide

Glass turntable

Rotating ring

Back Side

SPECIFICATIONS

Summary of Contents for MS-1071MC





































Search results

Summary of Contents for MS-1071MC

Reviews:

Related manuals for MS-1071MC

Brands by name

Popular brands

LG MS-1071MC, Service Manual

Search results

Summary of Contents for MS-1071MC

Reviews:

Related manuals for MS-1071MC

Brands by name

Popular brands