LG LW332 Series Owner'S Manual Download Page 32

Page: 32 / 84

Operation and settings

Maintenance

System reboot

Click the [Reboot] button to restart the IP device. It

takes some minutes for the IP device to start again.

Backup and Restore

Backup: To take a backup all of the settings.

If necessary, it make possible to return to a

backuped configuration. Click this button

and follow the instructions on the browser

to specify the folder and save the setting

data of the IP device. This configuration

backup can be restored whenever needed.

Restore:
1. Click the [Browse] button.
2. Find and open the file in which the

configuration setting data is stored.

3. Click the [Restore] button and the

system settings will be restored and

reboot the system.

Notes:
•

Backup and Restore can happen on IP

device having the same version of firmware.

This feature is not intended for multi-

configurations or for firmware upgrades.

Summary of Contents for LW332 Series





















































































Search results

Summary of Contents for LW332 Series

Reviews:

Related manuals for LW332 Series

Brands by name

Popular brands

LG LW332 Series, Owner'S Manual

Search results

Summary of Contents for LW332 Series

Reviews:

Related manuals for LW332 Series

Brands by name

Popular brands