background image

INSTALLATION

ENGLISH

2

3

Form the pipings

1

Wrap the connecting portion of indoor unit
with the Insulation material and secure it
with two Plastic Bands. (for the right pip-
ings)
• If you want to connect an additional drain
hose, the end of the drain-outlet should
keep distance from the ground. (Do not dip
it into water, and fix it on the wall to avoid
swinging in the wind.) 

2

Tape the Pipings, drain hose and
Connecting Cable from bottom to top.

3

Form the pipings gathered by taping along
the exterior wall and fix it onto the wall by
saddle or equivalent.

4

Tape the Pipings and Connecting cable
from bottom to top.

5

Form the pipings gathered by taping along
the exterior wall, and make the trap pre-
vent water from entering into the room. 

6

Fix the pipings onto the wall by saddle or
equivalent

In case of the Outdoor unit being
installed below position of the Indoor
unit. 

In case of the Outdoor Unit being
installed above position of the Indoor
Unit. 

Trap is required to prevent water from entering 

into electrical parts.

Seal a small opening

around the pipings

with gum type sealant.

Taping

Drain hose

Pipings

Connecting
cable

Power supply
cord

Seal a small opening 
around the pipings 
with gum type sealant.

Trap

Summary of Contents for LT-C282PLE0






























Reviews: