LG LRSC26920TT Service Manual Download Page 48 | Manualshive

Page: 48 / 106

background image

1. Operation Principle

1-1. Operation Principle of Icemaker

1. Turning the Icemaker stop switch off (O) stops the icemaking function.
2. Setting the Icemaker switch to OFF and then turning it back on will reset the icemaker control.

OPERATION PRINCIPLE AND REPAIR METHOD OF ICEMAKER

- 54 -

• Adjusts EJECTOR to Start Position with power on.

Power On

Start Position

Icemaking

Mode

Dump

Mode

Park Position

Fill

Test Mode

• Waits until water becomes cold after starting the
ice making operation.

• Runs MOTOR to drop ice from the tray to the ICE BIN.

• Performs Icemaking Mode after supplying water by operating
the SOLENOID in ICE VALVE.

• To operate LINE and SERVICE, press and hold the water supply
control switch for 3 seconds. The icemaker will run through
3 stages:
Dump Fill Icemaking.

• With the detect lever, checks if the ICE BIN is full.

«
...
46
47
48
49
50
...
»

Summary of Contents for LRSC26920TT











































































































Reviews:

No comments

Related manuals for LRSC26920TT

Modular 3000 Series

Brand: U-Line Pages: 12

Brand: U-Line Pages: 19

Brand: U-Line Pages: 30

Brand: U-Line Pages: 28

Brand: U-Line Pages: 31

Brand: Samsung Pages: 466

Brand: TCL Pages: 44

Brand: Avanti Pages: 28

Brand: Arctiko Pages: 20

Brand: U-Line Pages: 24

Brand: Amana Pages: 17

Brand: Bauknecht Pages: 10

Brand: Blomberg Pages: 90

8.436.545.201.527

Brand: Svan Pages: 80

Brand: Samsung Pages: 466

Brand: Samsung Pages: 466

Brand: Samsung Pages: 466

Brand: Jocel Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands